background image

10

  Mode Setting Switch
(Factory-preset setting)

OFF   ON

Adjustment switch

Backlight Compensation switch

Shutter Speed switch

IRIS

F.ADJ
   BLC
   1/60             1/100

OFF    ON

 1/60      1/100

OFF   ON

OFF   ON

OFF   ON

OFF   ON

OFF   ON

OFF   ON

8. ABOUT THE MODE SETTING SWITCH

Set the Mode Setting switch for the best possible picture reproduction depending on installation conditions.

8.1. Adjustment Switch

Set this switch when adjusting the lens focus.(Provides the same effect as when using the ND filter.)

Standard position : 

Set to OFF after lens adjustment completion. Set to this position during normal use.

Adjustment position (during adjustment) :

Use this position when focusing the lens. If the focus is adjusted for a subject under
good lighting conditions, the subject may go out of focus when conditions become
dark. Set the Adjustment switch to ON only when performing focus adjustment.

Note:

The color of the screen may periodically vary under fluorescent lighting when the

Adjustment switch is set to ON.

8.2. Backlight Compensation Switch

Set this switch so that the subject is not displayed in black when backlit.

Standard position : 

Set to this position during normal use. Backlight Compensation function does not
operate when the switch is set to this position. 

Backlight Compensation position (when backlit) :

This position prevents images from being displayed in black when the image is
backlit. 

8.3. Shutter Speed Switch

Set this switch to the ON position when annoying screen image flicker is detected. 

Standard position : 

Set to this position during normal use. 

Shutter Speed position :

Annoying screen flicker may result under fluorescent lighting in areas operating with a
power frequency of 50 Hz. In such cases, set the Shutter Speed switch to the ON
position to permit a flicker-free picture to be viewed.

Note:

If the Shutter Speed switch is set to the ON position, sensitivity is reduced compared

to operation in the OFF position. When using the camera in a dark location, or where
light flicker is not an annoyance, set the switch to the OFF position.

Summary of Contents for C-CV24-2 NTSC













Reviews: