Toa A-1706 Operating Instructions Manual Download Page 11

11

12. SPECIFICATIONS

Model No. 

A-1706 

A-1712 

A-1724

Power Source 

220 – 230 V AC or 240 V AC, 50/60 Hz

Rated Output 

60 W 

120 W 

240 W

Power/Current Consumption 

150 W (rated output),

258 W (rated output),

532 W (rated output),

60 W (EN60065) 

105 W (EN60065) 

220 W (EN60065) 

Under 150 mA (when 

Under 320 mA (when 

Under 60 mA (when 

power switch is OFF)

power switch is OFF) 

power switch is OFF) 

Frequency Response 

50 – 20,000 Hz (±3 dB)

Distortion 

Under 2% at 1 kHz, rated power

Input 

MIC 1 – 6: 

–60  dB*

1

, 600 

Ω

, electronically-balanced, combined type of

XLR-3-31 equivalent and phone jack 

AUX 1 – 2: 

–20  dB*

1

, 600 

Ω

, electronically-balanced, combined type of

XLR-3-31 equivalent and phone jack 

(Either MIC 5 or AUX 1, and either MIC 6 or AUX 2 selectable)
AUX 3 – 4: 

–20 dB*

1

, 10 k

Ω

, unbalanced, RCA pin jack 

AUX 5: 

–20  dB*

1

, 10 k

Ω

, unbalanced, combined type of XLR-3-31

equivalent and phone jack 

PWR AMP IN: 0 dB*

1

, 600 

Ω

, unbalanced, RCA pin jack 

(An equalizer or other signal processor connectable between LINE OUT
and PWR AMP IN terminals) 

Output REC: 

dB*

1

, 600 

Ω

, unbalanced, RCA pin jack 

LINE: 0 

dB*

1

, 600 

Ω

, unbalanced, RCA pin jack 

SPEAKER SELECTOR:  2 zone, high impedance*

2

(100 V line), individual

selector key, M4 screw terminal*

3

DIRECT SPEAKER OUT: High impedance*

2

(100 V line), M4 screw terminal*

3

,

Low impedance (4 – 16 

Ω

), M4 screw terminal*

3

Note:

Both Low and High impedance terminals cannot be used at the same time.

Phantom Power

ON or OFF for each MIC 1 – 6 with switch setting 

S/N Ratio

Over 100 dB (Master volume: min) 

(Band Pass: 20 – 20,000 Hz)  Over   76 dB (Master volume: max) 

Over   60 dB (MIC 1 – MIC 4) 
Over   53 dB (MIC 5, MIC 6) 
Over   76 dB (AUX 1 – AUX 5) 

Tone Control

Bass: ±10 dB at 100 Hz, Treble: ±10 dB at 10 kHz

Control Input 

REMOTE VOLUME: M3 screw terminal*

3

POWER REMOTE:  No-voltage make contact input 

Open voltage: 28 V DC (when the unit's power is OFF)
Short-circuit:  Under 10 mA, M3 screw terminal*

3

Indicator 

5-point LED output level meter, Power indicator LED, Zone indicator LEDs 

Operating Temperature 

–10°C to +40°C 

Finish

Panel: ABS resin, black, hair line 
Case:  Steel plate, black 

Dimensions 

420 (w) x 107.7 (h) x 367 (d) mm

Weight 

9.3 kg 

12.6 kg 

13.5 kg 

*

1

0 dB = 1 V 

*

2

167 

Ω

(A-1706), 83 

Ω

(A-1712), 42 

Ω

(A-1724)

*

3

Distance between barriers on the above screw terminals: 7 mm (M3 screw), 9 mm (M4 screw) 

Note:

The design and specifications are subject to change without notice for improvement. 

• Accessories

AC power cord  ................................................. 1 
Terminal cover  ................................................. 1 
Terminal cover mounting screw (M4 x 8) ......... 2 

• Optional products

Rack mounting bracket: MB-25B 
Volume control cover:  YA-920 
Perforated panel: 

PF-013B

Summary of Contents for A-1706













Reviews: