background image

 

172-65237A-01  (J10)    11  Mar  2021

 

14 

TLV EXPRESS LIMITED WARRANTY 

Subject to the limitations set forth below, TLV Corporation, a North Carolina corporation 
(“

TLV

”) warrants that products which are sold by it, TLV CO., LTD., a Japanese corporation 

(“

TLVJ

”) or TLV International, Inc., a Japanese corporation (“

TII

”), (hereinafter the 

Products

”) are designed and manufactured by TLVJ, conform to the specifications 

published by TLV 

for the corresponding part numbers (the “

Specifications

”) and are free 

from defective workmanship and materials. With regard to products or components 
manufactured by unrelated third parties (the “

Components

”), TLV provides no warranty 

other than the warranty from the third party manufacturer(s), if any. 

Exceptions to Warranty 

This warranty does not cover defects or failures caused by: 

1.  improper shipping, installation, use, handling, etc., by other than TLV or service 

representatives authorized by TLV; or 

2.  dirt, scale or rust, etc.; or 
3.  improper disassembly and reassembly, or inadequate inspection and maintenance by 

other than TLV or service representatives authorized by TLV; or 

4.  disasters or forces of nature or Acts of God; or 
5.  abuse, abnormal use, accidents or any other cause beyond the control of TLV; or 
6.  improper storage, maintenance or repair; or 
7.  operation of the Products not in accordance with instructions issued with the Products 

or with accepted industry practices; or 

8.  use for a purpose or in a manner for which the Products were not intended; or 
9.  use of the Products in a manner inconsistent with the Specifications; or 
10. use of the Products with Hazardous Fluids (fluids other than steam, air, water, 

nitrogen, carbon dioxide and inert gases (helium, neon, argon, krypton, xenon and 
radon)); or 

11. failure to follow the instructions contained in the TLV Instruction Manual for the 

Product. 

Duration of Warranty 

This warranty is effective for a period of the earlier of: (i) three (3) years after delivery of 
Products to the first end user in the case of sealed SST-Series Products for use in steam 
pressure service up to 650 psig; (ii) two (2) years after delivery of Products to the first end 
user in the case of PowerTrap

®

 units; or (iii) one (1) year after delivery of Products to the 

first end user in the case of all other Products. Notwithstanding the foregoing, asserting a 
claim under this warranty must be brought by the earlier of one of the foregoing periods, as 
applicable, or within five (5) years after the date of delivery to the initial buyer if not sold 
initially to the first end user. 

ANY IMPLIED WARRANTIES NOT NEGATED HEREBY WHICH MAY ARISE BY OPERATION OF 
LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE AND ANY EXPRESS WARRANTIES NOT NEGATED HEREBY, ARE 
GIVEN SOLELY TO THE INITIAL BUYER AND ARE LIMITED IN DURATION TO ONE (1) YEAR 
FROM THE DATE OF SHIPMENT BY TLV. 

Exclusive Remedy 

THE EXCLUSIVE REMEDY UNDER THIS WARRANTY, UNDER ANY EXPRESS WARRANTY OR 
UNDER ANY IMPLIED WARRANTIES NOT NEGATED HEREBY (INCLUDING THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE), IS 

REPLACEMENT

; PROVIDED: (a) THE CLAIMED DEFECT IS REPORTED TO TLV IN WRITING 

WITHIN THE APPLICABLE WARRANTY PERIOD, INCLUDING A DETAILED WRITTEN 
DESCRIPTION OF THE CLAIMED DEFECT AND HOW AND WHEN THE CLAIMED DEFECTIVE 

Summary of Contents for J10

















Reviews: