background image

 

172-65218MA-04  (DC3A-H)      7  Oct  2021

 

1

 

Contents

 

 

Introduction ....................................................................... 1

 

Safety Considerations ....................................................... 2

 

Specifications .................................................................... 4

 

Configuration ..................................................................... 5

 

Installation ......................................................................... 6

 

Maintenance ...................................................................... 7

 

Disassembly/Reassembly ................................................. 8

 

Troubleshooting .............................................................. 11

 

TLV EXPRESS LIMITED WARRANTY ........................... 12

 

Service ............................................................................ 14

 

 
 

 

Introduction 

 

Thank you for purchasing the TLV cyclone separator trap for air. 

 

This product has been thoroughly inspected before being shipped from the 
factory. When the product is delivered, before doing anything else, check the 
specifications and external appearance to make sure nothing is out of the 
ordinary. Also be sure to read this manual carefully before use and follow the 
instructions to be sure of using the product properly. 
 
This cyclone separator trap features a built-in free float air trap and uses 
centrifugal force to separate condensate from air.   
The combination of separator and built-in trap makes this product suitable for 
use in locations where a separator would be installed together with a trap. 
 
If detailed instructions for the special order specifications or options are not 
contained in this manual, please contact TLV for full details. 

 

This instruction manual is intended for use with the model(s) listed on the 
front cover. It is necessary not only for installation but for subsequent 
maintenance, disassembly/reassembly and troubleshooting. Please keep it in 
a safe place for future reference. 

 

Summary of Contents for DC3A-H
















Reviews: