background image

  
 

 

 

 

www.tkequip.com

 

(956) 796 - 9411

 

TABLE OF CONTENTS 

1.Serial Number Location .............................................. 3 

2.Parts Ordering Procedure .......................................... 3 

3.Operating Instructions ............................................... 4 

4.Safety Precaution ....................................................... 5 

5.Safety Notice & Decals ............................................... 6 

6.Before Operating........................................................ 6 

7.Operation Instruction................................................. 7 

8.Adding Fluids & Towing ............................................. 8 

9.Service Instructions .................................................. 10 

10.Maintenance Schedule .......................................... 11 

11.Replacements ......................................................... 12 

12.Equipment Specs .................................................... 13 

13.Troubleshooting ..................................................... 14 

14.Warranty ................................................................ 15 

15.Warehouse Locations ............................................. 17 

16.Additional Notes .................................................... 18 

17.Parts List Breakdown ............................... Attachment 

 

Summary of Contents for RAM70H



















Reviews: