No
washing
Abnormal
draining
Abnormal
spin
Identify usual trouble of washer
List of faults and inspection
Faults
Inspection Items
No water
flows in
! If the power is off or the fuse is burned out.
! If the water supply is cut off or the water pressure is too low.
! If the inlet hose is properly connected and the water tap is opened.
! If the filtering screen of inlet valve is blocked by dirt.
! If the coil of inlet valve is damaged. (The slight electromagnetic
sound is normal phenomenon when the inlet valve is switched on)
! If the "Start / Pause" button is pressed after the power
switch is pressed.
! If the door lid is closed.
! If all clothing piled largely at one side of barrel or the clothing
is excessively placed.
! If the washer is not placed in stable condition or it is placed in
inclination state. (The ground is not flat).
! If the motor belt is loosened.
Note: During the de spin process, if washing are piled at one side of the spin barrel,
it will cause unbalance of spin barrel resulting in striking. At this moment, the
computer inside the washer will feel this unbalance phenomenon and will automatically
correct it ( fill in water Washing ). However, if unbalance situation is not removed after
continuous three corrections, which means the computer auto-correction can not
resolve the problem. Then the user has to manually and evenly place the clothing
inside the barrel to solve the problem.
When the washer is in trouble, please contact local service office or the sales service
department of our company and the customer should not dismantle the machine without
permission.
If the washer can not work normally, or appear abnormity or alarms, please check and
correct
as follows.
! If the water drain hose is placed very high.
! If the end of water drain hose is sealed in pond.
! If the internal rubber ring of drain valve is blocked by dirt.
! If the power is off or the fuse is burned out.
! If the power supply voltage is too low.
! If the water amount reaches to the required water level.
(The washer will not work if the water amount does not reach the
required water level)
! If it is set to "Delay" washing mode. (It will only start to work
until the reservation time reached)
17
Malfunction display and solutions
When the washer is in trouble, please contact local service office or the sales service
department of our company and the customer should not dismantle the machine
without permission.
If the washer can not work normally, and the abnormal indication is shown in the nixie
tube window or the machine alarms, please check and correct as follows.
18
Technical specifications
360W
50
Hz
526×536×915(mm)
240V~
31 kg
Size
Rated input
power
Rated
voltage
Rated
frequency
Net weight
Rated capacity of wash
and spinning
Minimum water pressure
permitted in the water inlet
Maximum water pressure
permitted in the water inlet
Gross weight
34 kg
4.5kg(dry clothes)
0.6Mpa
0.1Mpa
Indication of fault
Cause of fault
Phenomenon of fault
Alarm of the
buzzing sound
Solution of alarm
Alarm for
injection
water
Entering water less than 16
minutes
,
reset water level
.
Alarm for
opening lid
Open the lid after start the
delay time
.
Open the lid
when the washer is spinning
.
Imbalance
alarm
Be examined imbalance
for the third time
.
Drain alarm
After draining for 4 minutes
,
does not finished to drain
.
The buzzer goes
on buzzing
sound for 10
seconds
.
If the alarm does
not be solved
,
every 16
minutes re
-
buzzs for 10
seconds
.
Open the lid to
deal with faults
,
then close the
lid to solve the
alarm
.
E1
E2
E3
E4
the new hose-sets supplied with the appliance are to be used
should not be reused appliance with ventilation openings in the base, that a carpet
must not obstruct the openings.
The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacture, its service agent
or similarly qualified persons in order to avoid a hazard.
and that old hose-sets
