Tinco AQUA28e Series Installation And Operation Manual Download Page 1

Page: 1 / 59

Installation/Operation

Manual

Pucada Tech

~ 1 ~ www.pucada.com

Model Series

ECO30i / GMC195IB & GMC195ID Series

ECO30e / GMC195OA Series

ECO24e GMC150OA Series

AQUA28i / GMS195ID Series

AQUA28e / GMS195OA Series

P21i / GMS150IB Series

P21e / GMS150OA Series

This appliance must be installed in accordance with



manufacturer’s installation instructions



Current AS/NZS 5601, AS/NZS 3000, AS/NZS 3500.4 wiring regulations and all Local Building, Water and

Gas fitting regulations

This appliance must be installed and serviced by an “authorized person” responsible for:

1. Give these instructions to the customers.

2. Correct commissioning of this appliance

3. Demonstrate the operation of unit to the customers before leaving

4. Ensure unit performs to the specification stated on the rating label

Failure to install this appliance according to these installation instructions may void warranty.

This appliance is not suitable for use as a pool heater

Summary of Contents for AQUA28e Series




























































Search results

Summary of Contents for AQUA28e Series

Reviews:

Related manuals for AQUA28e Series

Brands by name

Popular brands

Tinco AQUA28e Series, Installation And Operation Manual

Search results

Summary of Contents for AQUA28e Series

Reviews:

Related manuals for AQUA28e Series

Brands by name

Popular brands