Daylight-Saving Time
This unit is a preset Clock: the clock is already preset to Eastern Standard Time. It’s simple to match settings to where you
live.
1. Set
the
DST Switch
to +1. The DST icon will appear on top of display and the time will advance 1 hour.
2. Set
the
DST Switch
to -1 to set the time back 1 hour.
Auto-Set Time and Date Settings
This model is equipped with an Auto-Set feature; the time and date have been set for Eastern Standard Time at the factory.
1. To change your time zone setting, press and hold the
Time Zone Button
. The current time zone will flash briefly at
the bottom of the display, then revert to the standard date display.
2. While the
Time Zone is flashing, press the
<<
and
>> Button
to select your time zone. The time display will show
the current time for the selected time zone. There are seven zones to choose from:
ATL
Atlantic Standard Time
EAS
Eastern Standard Time
CEN
Central Standard Time
MTN
Mountain Standard Time
PAC
Pacific Standard Time
ALS
Alaskan Standard Time
HAI
Hawaiian Standard Time
Setting Time and Calendar
1. Press and hold the
Clock Adjust Button
located on the back of the unit for 2 seconds until the time display flashes.
If the time is correct, press the
Clock Adjust Button
again to accept the setting. Otherwise, press the
<<
or
>> Button
to adjust the time (hold for a few seconds to advance or reverse rapidly). Remember to set the correct AM or
PM time. (An icon at the upper right hand corner of the display is the
PM Indicator
;
there is no AM indicator
). When
the correct time is displayed, press the Clock Adjust button to confirm. The year display will flash.
2. Press the
Clock Adjust Button
to accept the current year setting or press the
<<
or
>>
Button until the correct
year is displayed. Press the
Clock Adjust Button
to confirm year setting after adjustment.
3. The display will change to show the date flashing. Press the
Clock Adjust Button
to accept the current date setting
or press the
<<
or
>>
Button
until the correct date is displayed (holding the button for a few seconds will advance
or reverse rapidly). Press the
Clock Adjust Button
to confirm the date setting after adjustment. You will hear 2
beeps indicating that clock and calendar setting is complete and it will exit the setting mode.
Setting Up the Ti700
Install/Replace the Remote Control Battery
The remote control battery is already installed at the factory. When the remote control stops operating or its range seems
reduced, it is time to replace the battery with a new one.
1. The battery door is located on the back end of the unit.
2. Slide the battery door open and remove old battery.
3. Insert a CR2032 battery, checking that the + and – ends of the battery
match the drawing inside the battery compartment.
4. Replace the battery door.
Note:
Make sure you dispose of battery properly (see your local regulations).
The Remote Control controls basic functions on the Ti700 and certain iPod
functions when the iPod is docked in the Ti700. For best results, aim remote
control towards the remote sensor on the upper right corner of the unit.
To check for iPod compatibility
The Ti700 is an advanced system and supports most updated iPod features. To ensure your iPod works properly with the
Ti700, please update your iPod firmware with the latest version. Please check the Apple website (www.apple.com) for
updates.
Install/Replace Clock Battery Backup
The Ti700 used 2 “AA” batteries backup battery system to provide continuous alarm operation and clock settings in the
event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally
disconnected, the display backlight will not remain lit, but the current time and alarm time settings will be temporarily
maintained. Otherwise, you must reset the time and alarm settings.
If the unit has no display or the Backup Battery Low Icon located on the top of the display is
flashing, it is time to replace the
backup batteries.
1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement.
2. Open backup battery compartment cover located on the bottom of the unit.
3. Insert two “AA” batteries, checking that the polarity ( + and - ends of the batteries) matches the drawing near the battery
compartment. Close the compartment cover.
Maintenance
l
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
l
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material
should be placed between it and the furniture.
l
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine,
thinner or similar materials can damage the surface of the unit.