background image

CONTENTS

SECTION 1

SECTION 2

BRIEF DESCRIPTION ............................................................... 1

QUICK OPERATION ................................................................. 3

Connect Power ................................................................................ 3
Connect Noise Antenna .................................................................. 3
Connect Outside Antenna ............................................................... 3
Connect Unit to Receiver Antenna Connector ................................ 3
Connect to Station Ground ............................................................. 3
Turn On Power ............................................................................... 3
Control Settings .............................................................................. 3
Tune in Noise on the Receiver........................................................ 3
Adjusting for Minimum Noise ........................................................ 4
High Frequency Operation (Over 20 MHz) .................................... 5
Reducing Hang Time For Break-In CW Or
         AMTOR/PACTOR Use ......................................................... 5
Broadcast Station Notch ..................................................................5
Broadcast Band Filter.......................................................................5

CONNECTIONS .......................................................................... 8

Power Requirements ....................................................................... 8
Vehicular Operation ....................................................................... 8
Main Antenna Input ........................................................................ 8
Radio Input ..................................................................................... 8
Noise Antenna ................................................................................ 8

CONTROLS & INDICATORS ................................................... 9

NOISE PHASE Control .................................................................. 9
PHASE RANGE pushbutton .......................................................... 9
FREQ RANGE pushbutton ............................................................. 9
NOISE GAIN Control .................................................................... 9

OPERATION .............................................................................. 10

Local Noise ................................................................................... 10
Active Antenna ............................................................................. 10
General Operating Hints ............................................................... 11

TECHNICAL INFORMATION ............................................... 12

Specifications................................................................................ 12

TROUBLESHOOTING ............................................................. 13

GENERAL THEORY OF OPERATION ................................ 15

SECTION 3

SECTION 4

SECTION 5

SECTION 6

SECTION 7

SECTION 8

Summary of Contents for ANC-4























Reviews:

Related manuals for ANC-4