background image

10

3 Year Guarantee 

In the unlikely event of this product becoming faulty due to defective material or 
manufacture within 3 years of the date of purchase, please return it to your supplier 
in the first year with proof of purchase and it will be replaced free of charge.  
For years 2 and 3 or any difficulty in the first year, telephone the helpline  
on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements  
(where agreed by Timeguard) the customer is responsible for all shipping/postage 
charges outside of the UK. All shipping costs are to be paid in advance before  
a replacement is sent.

9. Manual Override Mode 

•  The light can be switched ON for longer time periods by use of the Manual 

Override Mode. This can be activated at night time (only) by using the internal 
wall switch or circuit breaker. Switch the internal wall switch twice (OFF/ON, 
OFF/ON) within 2 seconds. 

•  The unit will now illuminate continuously for 6 hours, or until it is switched  

back into Auto Mode.

•  To return to Auto Mode, switch the internal wall switch OFF and then back  

ON again within 2 seconds.

•  The unit will return to its Auto Mode and will operate normally as set up.

Summary of Contents for PDFMMINIL













Reviews: