In the classroom, the Time Timer can be used to set time
limits, measure the duration of activities and train students
to make better use of available time. Use the Time Timer
products to:
• Time standardized tests
• Monitor math and writing speed tests
• Measure study periods and lunch periods
• Regulate computer time
• Administer duration drills
• Show time left to play, get ready or clean up
Using Time of Day and Alarm
Press MODE (lower
left) button until the
watch shows the Time,
displayed both in
traditional “analog”
form, and also in
digital format in center.
Notice that the Hour
hand is continuously
lit, while the minute
hand flashes slowly.
There is also a second
hand sweeping
around.
Press TIMER (upper right) button to see the Time of Day
alarm setting. The watch returns to current time after a
few seconds. Or, press MODE twice to see current time
immediately.
When the Time of Day alarm sounds, press any button to
silence it.
To change the settings for Time of Day or Time of Day
Alarm, see the instructions below.
Setting the Watch
The watch uses a standard setting procedure to set all
modes. It works as follows:
• Press and hold “S1” to enter setting mode
• Press “S2” to change the field to set
• Press “S3” to change the value of the field being set
• Press “S4” to exit setting mode
Setting the Timer
The timer must be stopped
before changing settings.
To set the timer, first press
the MODE button until you
see the Time Timer’s red
dial display appear. Press
and hold the S1 button
(upper left) for about
three seconds, until
the numbers in the
middle begin to
flash, indicating that
you have entered
setting mode.
Press S2 (upper right) to cycle through the fields you can
set. The fields are: Time setting
→
Alarm On/Off
→
Pre
Alarm On/Off
→
Time setting (Note that the Pre Alarm can
only be set if the Alarm is turned On).
Press S2 until you see digits in the center of the display.
Now you can set the timer. Press S3+ (lower right) to
increase the timer set point, and press S3– (lower left) to
decrease the set point. You will see both the digits and
also the dial size increase or decrease.
Setting Notes:
1. You can either press and release S3+ and S3– to
change field values, or “press and hold” either of the
S3 buttons to rapidly change the field value.
2. As you pass through each hour while setting, rapid
advance stops. This helps avoid overshooting your
desired set point.
3. The timer can be set to a minimum of 1 minute and a
maximum of 12 hrs.
4. You can return to the default timer setting of 60
minutes by simultaneously pressing S3+ and S3–.
Once you have set the desired time, press S2 once to
change Alarm On/Off Setting. You will see the word “ON”
or “OFF,” plus an alarm
•
3
symbol, both flashing. Press
S3+ or S3– to turn the Alarm on or off.
If you have turned the Alarm ON, you can now change
the Pre-Alarm settings by pressing S2 again. Again, the
Pre-Alarm can only be set if the Alarm is ON. If the Alarm
is OFF, pressing S2 will return you to the Time setting
field. In Pre-Alarm set, you will see the word “ON” or
“OFF,” plus TWO alarm
•
3
symbols. The Pre-Alarm symbol
(smaller and on the left) will be flashing, along with ON
or OFF. Press S3+ or S3– to turn the Pre-Alarm on or off.
Pressing S2 again will return you to the Timer setting.
Press S4 once (upper left) to exit setting mode. Leaving
the watch unattended for 30 seconds in set mode causes
it to save any changes and then exit set mode.
Setting the Current Time of Day and
Time of Day Alarm
Press MODE (lower left) to change to Time of Day mode.
Press and hold S1 (upper left) until the Hour “hand” and
digits begin to flash, indicating that you have entered set
mode.
Press S2 (upper right) to cycle through the fields you can
set. The fields are: Hour
→
Minute
→
Second
→
(Time
of Day) Alarm On/Off
→
Alarm Hour
→
Alarm Minute
→
Hour
Press S2 until the Hour hand and digits are flashing. Set
the current Hour by pressing S3+ (lower right) to increase
the Hour setting, or pressing S3– (lower left) to decrease
the setting. Note that the watch has “AM” and “PM”
indicators.
Note:
You can either press and release S3+ and S3– to
change field values, or “press and hold” either of the S3
buttons to rapidly change the field value.
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
AM
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
Hour
hand
Minute
hand
flashing
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
TIME
TIMER
0
5
10
15
55
20
25
30
35
40
45
50
30M
WATER RESIST
. .
4
Pre-alarm is ON
Alarm is ON
S1 & S4
S3–
S3+
S2
