background image

P 12 

of

 17

P 13 

of

 17

FIGURE 1, M7-22 SECTIONS 
OF MAIN CONTROL VALVE

Jam Nut

Port Relief

 

NOTE

To get proper pressure from the Port Reliefs, it may be necessary 
to turn the POR inward on the implement pump. See Figure 2 on 
Page 1 for POR location on implement pump.

Port Reliefs should be 500 psi higher than the working pressure 
in the valve section.

EXAMPLE

If the implement pump valve LS Relief pressure is 4200 psi, set 
the Port Relief pressure to 4700 psi.

3.  Back out the Port Relief until the needle on the gauge starts to move and

 tighten the jam nut once the relief is properly 

set. See Figure 1 above.

4.  Reset the Pump POR and LS settings as necessary.

LS Relief, PORT B
LS Relief, PORT A

FIGURE 2, MAIN CONTROL VALVE SECTIONS

Port Relief

LS Relief

Jam Nut

ADJUSTING THE PORT RELIEFS ON THE M7-22 MID-SECTION PROCEDURE END

c

haNGiNG

 M

iN

. d

iSpLaceMeNT

Some operators prefer having more speed while in driving Turtle mode. Turning the Min. Displacement screw clockwise 
increases user speed while in Turtle mode.

The adjustment screw is located on the track drive motor, forward/center inside. See Figure 1 on the next page.

TL/TN-775 M

AchiNe

 i

NiTiAL

 S

eT

-U

P

 G

Uide

S

ecTioN

 10 

&

 S

ecTioN

 11

Summary of Contents for TL775 Series























Reviews: