Timberk AC TIM 18LC DT3, Instruction Manual

Page: 5 / 17

www.timberk.com • Electric air conditioner www.timberk.com • Electric air conditioner
8
9
7. OPERATING MODES
NOTE:
If there is a difference between set and actual air
temperature in DRY mode, the conditioner will
automatically turn on in COOL or FAN modes.
ATTENTION!
Maintenance and service air conditioner must carry out
specialist.
8. MAINTENANCE
If the conditioner is not used for a long time, remove batteries from the
board or else electrolyte may leak and damage the board.
In normal operation of the conditioner average service life of batteries will
be about a half-year.
Replace batteries, if command receiving is not confirmed with an audio
signal, or if the display does not show a sign of command transfer.
When generating commands from the remote control board, point an IR-
radiator on a remote-control signal receiver situated on the indoor unit.
Hold the remote control board at the distance of no more than 8 m from
the indoor unit.
AUTO mode
The auto mode on and off is turned on and off with the use of the button
“MODE” on the remote control board.
1. While working in the AUTO mode, a microprocessor will automatically
select COOL, FAN, HEAT or DRY modes based on the difference between
actual and preset air temperature indoors.
2. If the AUTO mode does not provide comfort conditions, select the mode
manually.
COOL, HeAT and FAN
1. Turn the conditioner on pressing the «ON/OFF» button.
2. Pressing the «MODE» button, select COOL, HEAT or FAN mode
manually.
3. Pressing the «TEMP» button (up-down), set the desired air temperature
indoors (except for FAN mode).
4. Pressing the «FAN SPEED» button on the remote control board, select
the fan rotation speed: AUTO, LOW, MIDDLE, HIGH, and the conditioner
will start working in accordance with the selected setting.
5. To turn the conditioner off, press the «ON/OFF» button once again.
In the FAN mode air temperature indoors is not set.
DrY
Turn the conditioner on pressing the «ON/OFF» button. Pressing the
Before cleaning switch the conditioner off.
Cleaning of the indoor unit and remote control board:
Indoor unit and remote control board should be cleaned with a dry soft
cloth.
If the indoor unit is too unclean, moisten the cloth with cold water.
It is prohibited to clean the remote control board with moist cloth.
In order to avoid the damage of paint or details of the conditioner, do not
clean it with brushes and do not leave them on the surface of indoor unit.
In order to avoid the damage of surface or deformation of the conditioner
details, do not clean it with petrol, solvents, cleaning powders or other
chemically active substances.
Before a sustained interruption in the conditioner work:
Turn the conditioner on for several hours in the FAN mode. It will allow you
to dry its inner cavities
Switch the conditioner off.
Remove the batteries from the remote control board.
Checks before starting:
Make sure that air inlet and return air grillages of the outdoor unit are not
blocked by foreign objects.
«TUrbO» mode
When pressing the «TURBO» button on the remote control board, the
conditioner will start working in turbo mode for maximum cooling (in cool
mode) or for maximum heating (in heat mode).
TImer mode
Procedure of timing:
If the conditioner is off, then press the “TIMER” button to activate the
automatic turning on. Pressing this button once again, set the time for
turning the conditioner on in the set time interval. To cancel the timer mode,
press the “TIMER” button once again.
If the conditioner is working, then press the “TIMER” button to activate
the automatic turning off. Pressing this button once again, set the time for
turning the conditioner off in the set time interval. To cancel the timer mode,
press the “TIMER” button once again.
«SLeeP» mode
Using this button, you may turn the sleep mode on and off. In this mode the
fan rotation speed will be low.
When the function «SLEEP», if the air conditioner operates in cooling mode,
set temperature will increase1°C in 2 hours and 2°C over 8 hours.When the
function «SLEEP», if the air conditioner operates in heating mode, the set
temperature will decrease2°C in 1 hour and another 2°C within 2 hours of
work. After 8 hours in SLEEP mode air conditioner turns off.
«MODE» button, select the DRY mode. The conditioner will start working
in the set mode. To turn the conditioner off, press the «ON/OFF» button
once again.
9. TROUBLESHOOTING
In case of emergency, please, use the troubleshooting methods shown in
tables. If it is impossible to solve problems with these methods, apply to
the service center.
Failure Possible reason Actions
The conditioner does
not work
Interruptions in power supply
Wait for restoration of power
supply
Batteries in the remote control
board are low
Replace the batteries
Time of tuming on is set by
the timer
Wait till the conditooner turns
on by the timer or cancel the
timer setting
Insufficient cooling or
heating capacity
The set air temperature is too
high or too low Set the air temperature
correctly
The air filter is clogged with dust Clean the air filter
Foreign objects block the air intel
and retum air grillages of the
outdoor unit
Remove foreign objects
The conditioner works,
but does not cool or
heat the room
A three-minute delay of
compressor tuming on
Wait a little
The air temperature is set
incorrectly
Set the temperature correctly