Thundercomm Thundersoft TurboX S625, User Manual, Page: 23 / 29

22
16 SMB1358_INT_GPIO59_EXT_CON 3.3v DI/DO GPIO
18 GPIO_139_EXT_CON 3.3v DI/DO GPIO
19 BLSP5_UART5_TX_EXT_CON 3.3v DI/DO
UART
21 BLSP5_UART5_RX_EXT_CON 3.3v DI/DO
23 BLSP5_I2C5_SCL_EXT_CON 3.3v DO
I2C
24 BLSP5_I2C5_SDA_EXT_CON 3.3v DI/DO
29 BLSP7_SPI7_MOSI_EXT_CON 3.3v DI/DO
SPI
31 BLSP7_SPI7_MISO_EXT_CON 3.3v DI/DO
36 BLSP7_SPI7_CLK_I2C7_SCL_EXT_CO
N
3.3v DO
37 BLSP7_SPI7_CS_I2C7_SDA_EXT_CON 3.3v DO
6,9,14,20,25,30,
34,39
GND GND PO
7,15,22,26,27,2
8,32,33
NC
Table 4.5-2 Extension Interface Definition
4.5.18 Camera Connector
The S625 EVB supports two 4-lane camera interfaces. 13MP and 13MP; 24MP at 30fps ZSL with dual-ISP;
13MP 30fps ZSL with single ISP. I2C signal pull up on SOM. The B to B connector part number is AXE530127D.
CSI 0 connector
PINs Signal Volta
ge
Type Description
3 CAM_I2C_SDA0 1.8 V
chan
nel
outp
ut
DIDO Camera control interface I2C serial data
5 VREG_L6_1P8 1.8V PO Camera IO power output, max current 100
mA
6 CAM_I2C_SCL0 1.8 V DO Camera control interface I2C serial clock
MIPI DSI0 signals for MIPI LCD;
9 VREG_L22_2P8 2.8 V PO
Camera analog power output,
max current 150 mA
10 VREG_L2_1P1 1.1 V PO
Camera digital power output,
max current 300 mA
11 MCAM_RST_N 1.8 V DO Camera control interface reset output
12 CAM_STROBE0 1.8 V DO Main camera STROBE signal
14 CAM_MCLK0 1.8 V DO Main camera clock output
16 CAM_CSI0_LANE3_CONN_P CSI DI
MIPI CSI 0
17 CAM_CSI0_LANE3_CONN_M CSI DI
19 CAM_CSI0_LANE2_CONN_P CSI DI
20 CAM_CSI0_LANE2_CONN_M CSI DI
22 CAM_CSI0_LANE0_CONN_P CSI DI
23 CAM_CSI0_LANE0_CONN_M CSI DI
25 CAM_CSI0_CLK_CONN_P CSI DI
26 CAM_CSI0_CLK_CONN_M CSI DI
28 CAM_CSI0_LANE1_CONN_P CSI DI
29 CAM_CSI0_LANE1_CONN_M CSI DI
1, 2, 7,
13, 15,
18, 21,
24, 27, 30
GND - -
GND
4, 8, NC - - NC
CSI 1 connector
PINs Signal Volta
ge
Type Description
3 CAM_I2C_SDA1 1.8 V
chan
nel
outp
ut
DIDO Camera control interface I2C serial data