background image

5

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE

USING SPRAY GUN

GENERAL SAFETY WARNINGS

Keep work area clean. 

Messy areas and cluttered workbenches invite personal 

injury and/or property damage.

Keep children and visitors away. 

All children should be kept away from the work 

area. DO NOT let children handle the compressor or extension cord. Maintain a safe 
distance for any person near the work area.

Operating any tools or equipment under the influence of drugs, alcohol, 
or medication can cause personal injury to yourself and others.
Wear proper apparel. 

Remove your jewelry before using this tool. Do not wear 

loose clothing, necklaces, rings, bracelets, or other jewelry, which may get caught 
in moving parts. Nonskid footwear and electrically non-conductive gloves are highly 
suggested while working. Wear protective hair covering to contain long hair.

Protect your eyes. The operation of this tool can result in foreign objects 
being thrown into the eyes, which can result in severe eye damage. 
Always wear eye protection that meets ANSI Z28.1 specifications during 

tool operation. Eyeglasses are not always safety glasses.
Be responsible for your hearing. Wear hearing protection during extended periods of 
operation.

Be responsible for your hearing.

 Wear hearing protection during extended 

periods of operation.

Summary of Contents for 4001J





















Reviews: