THUNDER TIGER TOMAHAWK XL, Instruction Manual & Parts Catalogue

Page: 9 / 27

8
F/S-FAIL SAFE
防暴衝設定
7
Release first 先放開
OFF
2.
1. Steering: Neutral
2. Keep brake or
trigger at neutral
1.
轉向中立
2.
保持煞車或油門扳機在中立點位置
完成對頻
Binding Complete
No Action
無須動作
Push for 10
sceonds
先持續按 10 秒
RX LED ： GREEN FLASH
TX LED
：
GREEN SOLID
RX LED
：
GREEN SOLID
TX 燈號：綠燈恆亮
RX 燈號：綠燈恆亮
RX
燈號：綠燈快速閃爍
RX LED : RED SOLID-2s-
>GREEN SOLID
RX 燈號：
紅燈恆亮 -2 秒 -> 綠燈恆亮
電車：轉向朝前，速控器煞
車油車：轉向朝前，
油門關
閉（怠速）煞車啟動
Release later
後放開
1. Keep brake
2. Swithch Off
OK!
1.
保持煞車
2.
關發射機
Step
步驟
a
b
c
d
e
f
TX Action
動作
完成對頻
Binding Complete
No Action
無須動作
No Action
無須動作
RX Action
動作
Check
確認
1.
1. 2.
or
_
_
How to Set the Fail Safe (F/S) Position
a. After binding the transmitter and receiver, you can continually set up the F/S position. Turn on the transmitter power and then
receiver power.
b. Press the “Binding SW” button on the receiver. 10 seconds later, the LED will turn green flash on the receiver.
(Caution! Don't release the “Binding SW” button now until STEP c has been completed.)
c. Move and hold the throttle trigger to the F/S servo position where you want to set. Keep steering wheel at Neutral. To set up
F/S with servo position at "Brake", first push the trigger to the brake position and hold. To set up F/S with servo position at
"Neutral", keep the trigger at neutral.
(Caution: Always set the throttle trigger to the neutral or full brake position incase of any unexpected control error!)
d. After the Step3, release the “Binding SW” button first and then the throttle trigger. The LED turns to solid “RED” and then
back to solid “GREEN” 2 seconds after. The F/S set up has now been activated.
e. F/S at "Neutral": To check the fail safe is working properly, by moving the throttle trigger to the full forward (full brake), hold it
on this position and then turn off the transmitter. The F/S function should move the throttle servo to "Neutral".
F/S at "Brake": To check the fail safe is working properly, by keeping the throttle trigger at neutral and then turn off the
transmitter. The F/S function should move the throttle servo to "Brake".
f. If the F/S set up fail, try the steps from a) ~f) again. After the F/S has been fully complete, you can just start your operation.
Transmitter first, receiver later.
a. 設定此功能前請先完成系統發射與接收之對頻。確定後，先打開發射機再開接收機電源。
b.
押著接收機對頻開關，約
10
秒鐘後
LED
會變為綠色快速閃爍
注意：步驟
3
完成前不要放開接收機對頻開關。
c.
同時移動油門扳機至您想要設定
F/S
伺服機位置。轉向舵輪保持中立點位置。
【如想要設定 F/S 油門伺服機位置為煞車，需先移動油門扳機至煞車位置不要鬆開。】
【如想要設定 F/S 油門伺服機為至為中立 , 保持油門扳機在中立點位置 , 不要移動油門扳機。】
注意：防暴衝油門伺服機位置建議設定為煞車或中立點，請勿設定為油門開啟位置，以免發生危險。
d. 此時你可以放開接收機對頻開關，再放開發射機油門板機。 LED 會變為恆亮紅燈，約 2 秒後又回到恆亮綠燈，此時表示 F/S 設定
成功。
e. F/S 油門伺服機位置為中立點 : 將油門扳機全煞車，關掉發射機電源，檢視 F/S 伺服機位置動作是否轉回中立點位置。 F/S 油門伺
服機位置為煞車
:
油門扳機保持中立點，關掉發射機電源，檢視
F/S
伺服機位置動作是否轉回煞車位置。
f. 檢查無誤後，開發射機開關，然後接收機關開始操作。