background image

1

Thunder Tiger Cloud Dancer 60 ARF (TTR4559)

Distributed in North America by Ace Hobby Distributors, Inc. • 2682 Walnut Avenue,Tustin, CA 92780

Phone: 714-544-0330 • www.acehobby.com • email: [email protected]

Cloud Dancer 60 ARF

Assembly Manual

Wingspan: 72" (1828mm)
Length: 57" (1447mm)
Wing Area: 840in2 (54.2 dm2)
Weight: 6.5-7 lbs.(3000-3200g)
Engine: .61 2 cycle

.91~1.20 4 cycle

Radio: 4 CH. 5 servos

Specifications:

Warranty

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

It does not cover any damage caused by use or modification. The warranty does not extend beyond the
product itself and is limited only to the original cost of the kit. By the act of building this user-assembled
kit, the user accepts all resulting liability for damage caused by the final product. If the buyer is not 
prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund.

JE6460

Notice: Adult Supervision Required

This is not a toy. Assembly and flying of this product requires adult supervision.

Read through this book completely and become familiar with the assembly and flight of this airplane.

Inspect all parts for completeness and damage. If you encounter any problems, call us for help.

Summary of Contents for Cloud Dancer 60 ARF

















Reviews: