background image

Cause

1. Fuel tank is empty
2. Contaminated fuel
3. Glow plug does not work

4. Glow plug igniter is not charged
5. Engine is flooded

6. Engine is overheating

7. Carburetor is incorrectly

adjusted.

8. Exhaust blocked 
9. Air cleaner blocked 

1. Idle speed set too slow

2. Air bubbles in fuel line.
3. Glow plug is fouled 

1. Engine is flooded 

2. Engine is seized  

1. Brake setting is incorrect

2. Worn out of brake pad

1. Transmitter and/or receiver

batteries are dead or weak.

2. Transmitter has low range

3. Servo linkage not adjusted

properly.

4. Rear wheel and rear swing arm

are not parallel. 

5. Steering Trim not adjust in the

neutral.

TROUBLESHOOTING

Solution

1.Add fuel the bike
2.Replace with new fuel
3.Replace the glowplug and see Step15

"PREPARING THE ENGINE" section.

4.Recharge the igniter
5. See Step16 "UNFLOOD AN ENGINE"

section.

6. Allow engine to cool, richen the "Fuel

Mixture"

7. Re-adjust carburetor, see

Step13"ADJUSTING CARBURETOR"
section 

8. Check exhaust, remove blockage.
9. Check air cleaner, remove blockage

1.Adjust idle speed screw, see

Step13"ADJUSTING CARBURETOR"
section.

2.Check for leaks in fuel line.
3.Replace glow plug, see Step15

"PREPARING THE ENGINE" section.

1. See Step16 "UNFLOOD AN ENGINE"

section.

2. Examine engine for damage

1. See Step12 "ADJUSTING

THROTTLE/BRAKE LINKAGE" section.

2. See Step 3 "INSTALLING

THROTTLE/BRAKE LINKAGE" section
to replace brake pad.

1. Replace the batteries or recharge.

2. Fully extend transmitter and receiver

antenna. 

3.  See Step2 "INSTALLING STEERING

SERVO LINKAGE" section to re-build
and re-adjust the steering servo linkage.

4. See Step 4 "INSTALLING THE SIDE

GUARD WIRE AND ADJUSTING THE
STABILITY" 
section to adjust the rear
wheel.

5. See Step 10 "OPERATING RADIO-

STEERING FUNCTION" section to
adjust neutral position.

Description

Engine does not start

Engine star ts, but
then stalls.

Shaft starter will not
rotate.

No brake control

Motorbike is difficult
to control

THUNDER TIGER CORPORATION

http://www.thundertiger.com

JD6599

Summary of Contents for 6301-F

















Reviews: