manualshive.com logo in svg

Thule Omnistor, Instructions Manual, Page: 10 / 28

Share
Download
Thule Omnistor Instructions Manual Download Page 10

10

CCD-0004167

Rev: 01/13/21

Clean the awning fabric regularly to remove any dirt and dust: 
- To do this, use water (water should be cold to lukewarm, never more than 100°F/37°C) with    
  30 ml mild detergent (for 10 L of water).  
- Soap down the fabric and leave the liquid to soak in for five minutes. 
- Rinse thoroughly with clean water. Make sure that the detergent is completely washed off. 
  Otherwise it can damage the fabric. 
- Leave the fabric to dry. Air dry only, never apply heat to the fabric.

Mildew is a fungus growth that looks like dirt. Vinyl coated polyester fabrics are mildew  
resistant because of a chemical biocide in the vinyl coating. Under ordinary conditions,  
mildew will not appear. However, in areas where high temperature and humidity are common, 
mildew can be a problem and require the material to be washed more frequently. Thoroughly 
rinse the fabric with clean water and allow to air dry completely before rolling up the awning.

When water collects on the top of the fabric, this is known as "pooling". This can occur during 
inclement weather or if a running air conditioner discharges over the awning. The water is 
dumped when the awning is retracted. It is recommended that if water accumulates on the top; 
retract the awning in steps (8"-12") to dump the water. This will help prevent the fabric from 
stretching or distorting.

If required, lubricate the joints of the awning with paraffin wax, teflon oil or silicone oil.

Check the awning regularly for any imbalance and wear, as well as damage to major parts.

Check the awning regularly: 
- Is the fabric free of damage? 
- Are the arms and front panel free of damage with no signs of wear? 
- Does the awning close properly?

Do not use oil based cleaners or any caustic, granulated, or abrasive type cleaners on your 
Thule product.

Do not use any sprays (e. g. insect repellent, hairspray) near the awning. This will soil the fabric 
or the water-repellent effect of the fabric will be lost.

CLOSE

 

THE AWNING

Summary of Contents for Omnistor





























Reviews:

No comments