background image

READ ALL INSTRUCTIONS

All the safety and operating instructions of your Thrax Audio 

equipment should be read before power is applied to the equipment. 

RETAIN OWNER'S MANUAL

These safety and operating instructions should be retained 

for future reference. 

HEED  WARNING

All  warnings  on  the  unit  and  in  the  operating  instructions  should  be 

adhered to. 

FOLLOW INSTRUCTIONS

:

 

All operating and use instructions should be followed. 

CLEANING

Unplug the unit from the wall outlet and leave for at least 30 min. - make sure 

the  unit  is  not  hot  before  you  start  cleaning.  Use  dry  or  damp  soft  cloth  to  clean  the 

surfaces. Do not use corrosive, abrasive or spray for cleaning. 

VENTILATION

Do not block any ventilation openings. Do not install near any heat sources 

such as radiators, heat registers, stoves, or other apparatus (including amplifiers). The unit 

should not be installed in a built-in location such as a bookcase or rack unless proper 

ventilation is provided.

GROUNDING

Do  not  defeat  the  safety  purpose  of  the  grounding-type  plug.  A 

grounding-type  plug  has  two  blades  and  a  third  grounding  prong.  The  third  prong  is 

provided  for  your  safety.  If  the  provided  plug  does  not  fit  into  your  outlet,  consult  an 

electrician for replacement of the obsolete outlet.

POWER CORD PROTECTION

Protect the power cord from being walked on or pinched 

particularly at plugs, convenience receptacles and the point where they exit from the 

apparatus.

LIGHTNING

Unplug  this  apparatus  during  lightning  storms  or  when  unused  for  long 

periods of time.

SERVICING

Refer all servicing to qualified service personnel. Servicing is required when 

the apparatus has been damaged in any way, such as if the power-supply cord or plug is 

damaged,  liquid  has  been  spilled  inside  the  appliance  or  it  has  been  exposed  to 

moisture, the appliance does not operate normally, or has been dropped.

DO  NOT  OPEN  THE  CABINET

There  are  no  user  serviceable  components  inside  this 

product. Opening the cabinet may present a shock hazard, and any modification to the 

product will void your warranty.

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain 

or moisture.

IMPORTANT SAFETY INSTRUCTIONS

3

Summary of Contents for Orpheus











Reviews: