background image

READ ALL INSTRUCTIONS

: All the safety and operating instructions of your Thrax Audio 

equipment should be read before power is applied to the equipment. 

RETAIN OWNER'S MANUAL

: These safety and operating instructions should be retained 

for future reference. 

HEED WARNING

: All warnings on the unit and in the operating instructions should be 

adhered to. 

FOLLOW INSTRUCTIONS

:

 

All operating and use instructions should be followed. 

CLEANING

: Unplug the unit from the wall outlet and leave for at least 30 min. - make sure 

the unit is not hot before you start cleaning. Use dry or damp soft cloth to clean the 

surfaces. Do not use corrosive, abrasive or spray for cleaning. 

VENTILATION

: Do not block any ventilation openings. Do not install near any heat sources 

such as radiators, heat registers, stoves, or other apparatus (including amplifiers). The unit 

should not be installed in a built-in location such as a bookcase or rack unless proper 

ventilation is provided.

GROUNDING

: Do not defeat the safety purpose of the grounding-type plug. A 

grounding-type plug has two blades and a third grounding prong. The third prong is 

provided for your safety. If the provided plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete outlet.

POWER CORD PROTECTION

: Protect the power cord from being walked on or pinched 

particularly at plugs, convenience receptacles and the point where they exit from the 

apparatus.

LIGHTNING

: Unplug this apparatus during lightning storms or when unused for long 

periods of time.

SERVICING

: Refer all servicing to qualified service personnel. Servicing is required when 

the apparatus has been damaged in any way, such as if the power-supply cord or plug is 

damaged, liquid has been spilled inside the appliance or it has been exposed to 

moisture, the appliance does not operate normally, or has been dropped.

DO NOT OPEN THE CABINET

: There are no user serviceable components inside this 

product. Opening the cabinet may present a shock hazard, and any modification to the 

product will void your warranty.

WARNING

: To reduce the risk of fire or electric shock, do not expose this apparatus to rain 

or moisture.

IMPORTANT SAFETY INSTRUCTIONS

3

Summary of Contents for Heros












Reviews: