manualshive.com logo in svg

THORLABS SL1325-P16, Operating Manual

Share
Download
THORLABS SL1325-P16 Operating Manual Download Page 3

 

Swept Source Laser 

14138-D02 Rev F 04/17/09                                                         Page 2 of 18 

Part 1. 

Introduction 

1.1. Important 

Notices 

 

ATTENTION USER! 

Please read the instruction manual carefully before operating the Swept Source 

Laser.  
All statements regarding safety and technical specifications will only apply when 

the unit is operated correctly.  

 

WARRANTY WARNING 

Do not open the unit under any circumstance.  
There are no user serviceable parts in this product. Opening the device will void 

your warranty. 
Any modification or servicing of this system by unqualified personnel renders 

Thorlabs free of any liability. 

 

Attention 

This  device  can  only  be  returned  when  packed  into  the  complete  original 

packaging, including all foam packing inserts. If necessary, ask for a replacement 

packing.  

 

ATTENTION USER! 

Check the supply voltage of the system 

before

 plugging in the Swept Source 

Laser. 
Make sure the included power cord for the Swept Source Laser is connected to a 

properly grounded power outlet (100V – 240V AC; 50Hz – 60Hz). 

 

Transportation and delivery may cause the Swept Source Laser to be warm or cool 

upon receipt. Please wait for the unit to reach room temperature before attempting 

to operate. 
Use a flat, dry, and stable surface to set up the system. 

Summary of Contents for SL1325-P16




















Reviews:

No comments

Brands by name

Popular brands

Load more brands