THORLABS PM5020 User Manual Download Page 59

Page: 59 / 65

Page 55

PM5020 Dual-Channel Benchtop Power and Energy Meter

Chapter 5 Specifications

Rev: 1.0, 18-Aug-2022

Pin

Function

Description

I/O 0

Input/Output Port or alternative function pass/fail or disable analog port to be set
in the

settings menu

I/O 1

Input/Output Port or alternative function pass/fail or disable analog port to be set
in the

settings menu

I/O 2

Input/Output Port or alternative function shutter control or shutter monitor

I/O 3

Input/Output Port or alternative function logging control or logging monitor

TRIG

Trigger Input/Output

GND

Ground

SCL

I2C Bus Clock

SDA

I2C Bus Data

3V3

Power Supply for Accessories, 3.3 V, 100 mA Max

5 V

Power Supply for Accessories, 5 V, 100 mA Max

5.4 Pin Fan Control

The PM5020 has a Fan Control Connector. The Pins are assigned as follows:

Pin

Function

Description

NTC1

Input External NTC1

GND

Ground NTC1

NTC2

Input External NTC2

GND

Ground NTC2

Fan1

Supply Fan1

GND

Ground Fan1

TAC1

Optional Tacho Signal of Fan1

Fan2

Supply Fan2

GND

Ground Fan2

TAC2

Optional Tacho Signal of Fan2

Summary of Contents for PM5020

































































Search results

Summary of Contents for PM5020

Reviews:

Brands by name

Popular brands

THORLABS PM5020, User Manual

Search results

Summary of Contents for PM5020

Reviews:

Brands by name

Popular brands