THORLABS M2MS Operating Manual Download Page 88

Page: 88 / 167

BP209 Series

7 Operation Instructions

Page 86

21424-D02

7.2.6.2 Connecting M2MS to the PC

The M2MS comprises integrated control electronics with translation stage controller, a USB 2.0
hub and a current source for the alignment laser.

Switch to enable Alignment Laser

Output connector for Alignment Laser

USB 2.0 hub output ports (to Beam Profiler)

USB 2.0 input (from PC)

Yellow indicator "Stage active"

Green indicator "Power On"

DC power supply input

M2MS power switch

Attention!

Prior to connecting the M2MS to the power supply, make sure the

transportation lock is re-

moved

! Otherwise the stage drive may be damaged!

Attention!

It is strongly recommended that only the supplied USB cables are used to connect the Beam
Profiler and the control PC to the M2MS.

The use of other than the supplied USB cables may lead to USB connection instabilities.

Attention

Do NOT connect the M2MS to a computer prior to installing the Beam Software!

1. Remove the

transportation lock

2. Connect AC power to the power supply and its output to the DC jack (

3. When using a BP209 Series Slit Beam profier, connect the beam profiler using the supplied

angled USB 2.0 cable to one of the USB hub outputs (3).

4. Switch the M2MS on (8). The green

Power On

indicator lights up.

5. Connect the M2MS to the PC using the supplied 3 m long USB 2.0 cable; do not start the

BEAM software yet.

6. The PC's operating system recognizes the connected new hardware and performs the driver

installation:

Summary of Contents for M2MS







































































































































































Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands

THORLABS M2MS, Operating Manual

Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands