THORLABS M2MS Operating Manual Download Page 62

Page: 62 / 167

BP209 Series

6 The Graphics User Interface (GUI)

Page 60

21424-D02

6.6.9.5 Plot Environment Data

In this window the position of the X and Y centroids can be logged together with the reading of
an externally connected Thorlabs TSP01 temperature sensor vs. time.

The temperature axis is located to the left (yellow curve), the centroid position axis (blue and
green curves) is shown to the right.

Toolbar Icon

Associated Action

Save Diagram or Image: Opens a dialog box to specify the properties of the
saved diagram or image.

Save Data: Opens a dialog box to specify the properties of the saved calcu-
lation data

Clear all plots

Show or Hide the grid in the diagram

Autoscale ON/OFF

Show or hide the cursor

Summary of Contents for M2MS







































































































































































Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands

THORLABS M2MS, Operating Manual

Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands