background image

18

Technical Specifications:

TD 295 MKIV

Drive system:

belt drive 
(precision-ground belt)

Motor:

electronically controlled 
AC synchronous motor

Speed:

33 and 45 rpm

Speed selection:

electronically

Platter:

304 mm / 2.3 kg, non-magnetic

Tonearm:

THORENS TP 41 equipped with 
pick-up cartridge AT 95E

Anti-skating:

by weight-on-string

Automatic functions:

semi-automatic

Automatic shut-off:

opto-electronic

Capacity of leads:

160 pF

Voltage/Power supply: mains transformer unit available 

for all major mains supplies

Dimensions: (WxDxH): 434 x 339 x 131 mm
Weight:

8.5 kg

Finish:

piano laquer black
piano laquer mahogany
piano laquer beige

In the event of further queries, we shall
be pleased to assist you by email: 
[email protected]
Technical modifications subject 
to change without prior notice.

THORENS Factory Warranty

In case a failure or malfunction occurs in your record player
during the warranty period we guarantee to replace any
defective part of this unit, or to repair the unit free of charge
in a service centre maintained or authorized by us. This fac-
tory warranty covers two years from the date of purchase.

If a defect or malfunction occurs within the warranty peri-
od you should inform your THORENS dealer or general
representative. If the unit has to be returned for repair or
service purposes you are kindly requested to send the unit
in its original shipping box whereby shipping charges and
insurance are to be covered from your side.

Any damage or malfunction caused by failure to observe
the instructions contained in this manual as well as dama-
ges occurred in transport or shipping are not covered by
this warranty.

This warranty will be void if the device has been modified,
disassembled or repaired by others than an appointed
THORENS service. NB: please be aware that there may be
additional warranty conditions issued and made applicable
by the THORENS representative in your country.

Summary of Contents for TD 295 MKIV





















Reviews: