The wall plate
A
is attached to the wall using 2x
W-A
screws and 2x
W-C
washers supplied. Use a stud detector to find and mark the position of the studs
in the chosen location. Offer up the wall plate using a spirit level to get it level and
mark the screw positions as shown
Fig.3
. Use a 4.5mm drill bit to drill 2x 55mm
deep holes as close as possible to the centre of the uprights. Attach the wall plate
using the screws and washers (see
Fig.4.
for studs 400mm apart and
Fig.5.
for
studs 600mm apart).
2. Attaching to Stud Walls
Tools required
3. Attaching to Concrete/Brick Walls
Tools required
Fig.6
Select the correct size bolts to fit the VESA holes for your TV
M-A
/
M-B
/
M-C
/
M-D
/
M-E
. Attach the TV plate
B
to the back of the TV by lining up the top VESA holes
and using bolts
M-A
/
M-B
/
M-C
/
M-D
/
M-E
and the washers
M-F
/
M-G
and spacers
M-H
/
M-I
(if required) to fix the TV securely to the adaptor brackets. Use the same
combination of bolts, washers and spacers to attach the two standoffs
C
to the
lower VESA holes.
4. Attaching the TV Plate and Standoffs to the TV
to give 0° Screen Tilt
Fig.8
The wall plate
A
is attached to the wall using 4x
W-A
screws, 4x
W-B
wall plugs
and 4x
W-C
washers supplied. Offer up the wall plate using a spirit level to get it
level and mark the screw positions as shown
Fig.6
. Use a 10mm drill bit to drill
4x 60mm deep holes. Insert the wall plugs
W-B
into the holes and attach the wall
plate using the screws
W-A
screws and washers
W-C
(see
Fig.7
).
Fig.7
1. Attaching to plasterboard
Tools required
Place the wall plate
A
in the position chosen and gently hammer in the first nail
W-D
on the extreme left or right end of the wall plate at the angle and to the depth shown
in
Fig.2
. Then check the plate is level (using a spirit level) before hammering in a nail at
the other end, next hammer in the remaining 18 nails.
Please Note:
Installation is best carried out by two people, one to hold the wall plate in
position and the other to hammer in the nails.
Be careful not to knock the nails all the way through the plasterboard.
Make sure the plasterboard is in good condition and has not been exposed to damp
at anytime.
Installation
A
W-D
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
400mm
Select the correct size bolts to fit the VESA holes for your TV
M-A
/
M-B
/
M-C
/
M-D
/
M-E
. Attach the TV plate
B
to the back of the TV by lining up the top VESA holes
and using the bolts
M-A
/
M-B
/
M-C
/
M-D
/
M-E
, washers
M-F
/
M-G
and spacers
M-H
/
M-I
(if required) to fix the TV securely to the adaptor brackets. Use the same combi-
nation of bolts, washers and spacers to attach the two standoffs
D
to the lower
VESA holes. If you want to adjust the -5° tilt angle slightly you can in some in-
stances add or remove spacers on the standoff.
6. Attaching the TV Plate and Standoffs to the TV
to give -5° Screen Tilt
Fig.9
600mm
