Pairing with the Thombox
During the countdown, remove the tab which protects the detector battery (remove the tab
before installing the detector in its final location).
G2 - OPENING DETECTOR FOR DOORS AND WINDOWS
When installed on a door or window, this device will detect any attempts at intrusion (detected
when the magnet is moved away) and transmits the information to a central unit which triggers
an alert.
Setup
Pairing with the Thombox
During the countdown, remove the tab which protects the detector battery (remove the tab
before installing the detector in its final location). Wait for 10-20 seconds.
G3 - ALARM REMOTE CONTROL
The remote control allows you to activate and deactivate your alarm system.
The buttons are typically assigned as follows:
When you press a button on the remote control, the LED on the remote control tells you if your
Thombox has received the instruction:
• Red LED: indicates that a radio transmission is taking place.
• Orange LED: the Thombox has not received the command sent from your remote control.
If this happens, try again or move closer to your Thombox.
• Green LED: the Thombox has received the instruction that you sent.
Pairing with the Thombox
During the countdown, hold down the 2 buttons at the top of your remote control for at least
5 seconds.
G4 - 720P IP CAMERA
Your camera allows you to take photos via the Thombox when movement is detected. Photos
are stored in the Thombox's 'Cameras' widget, and the live image from the camera is also
accessible from this same widget.
Setup
The camera connects to your wired or wireless (WiFi) network. To set up the camera, a wired
connection is required (even if you will later decide to use a wireless connection).
Launch the 'IP Camera Search Tool' included on the CD to locate the camera on your network
then double click on the corresponding entry.
Connect to your camera from your browser:
Select the language of your choice. The default username is "admin" and there is no pre-set
password.
The camera will immediately ask you to change the login username:
Type your new username and the password of your choice.
Optional: setting up a wireless connection
Connect to your camera using the username and password you have just created.
Click on the Réglages [Settings] tab then on the 'Assistant de configuration [Configuration
wizard]' button to launch the wizard which allows you to set your camera up for WiFi:
Once you have finished, you can disconnect the network cable from your camera and close
the page.
You can now install your camera:
Make sure the camera is properly secured to prevent it from falling.
Once you have set up the device, you can adjust the focus of the image if it is lacking
sharpness. Gently rotate the lens to adjust the focus.
WARNING: Do not unscrew the lens completely or force it.
ø4mm
12mm
max
25mm
studs
2mm
66mm
22mm
- Attach the magnet using double-sided
tape or the screws provided.
- Attach the magnet opposite the two
studs on the detector.
Arms your entire system,
for example when you
have left the property.
Disarms the whole
system.
Arms part of your system,
when you are present
and want to arm your
protection overnight, for
example.
Triggers your system in the
event of an emergency,
illness or other problem.
Reset
Power
Wireless
WPS
camera
Mains adapter
Modem/router connected to the
internet
Pairing with the Thombox
Your camera is optimised for use with a Thombox. Go into the interface of your Thombox to
pair your camera and click on 'Ajouter une nouvelle caméra [Add new camera]' in the Cameras
widget:
Tick the box on the row corresponding to your camera, then click Ajouter [Add].
If your camera has not been detected, enter the address of your camera as indicated by the
IP Camera Search Tool software:
Warning: the default address of your camera ends with ':88'; you should also copy it and the
IP address of your camera in the Thombox widget. Tick the relevant camera, then click on
Ajouter [Add].
Your camera will be configured automatically in the Thombox interface. Enter your username
and password:
If you want your camera to send images to the Thombox when motion is detected, click on
the 'Copier les réglages dans la caméra [Copy settings to camera]' button at the bottom of the
window. Your Thombox will then write the destination for the images to the camera settings.
This completes the configuration.
(Click on the
icon in the cameras widget on your Thombox to display more details on the
functions and options available).
tick the row
corresponding to
your camera
