Complete Solutions in Emergency Lighting
STANILITE
Complete Solutions in Emergency Lighting
STANILITE
© Copyright 2013. Thomas & Betts Australasia ABN: 062 074 810 898
.
Rev: 3.0 26 July 2013 1
© Copyright 2013. Thomas & Betts Australasia ABN: 062 074 810 898
.
Rev: 3.0 26 July 2013 4
Thomas & Betts Australasia. ABN 062 074 810 898
Head Office: Unit D3, 3-29 Birnie Avenue, Lidcombe NSW 2141, Australia
Manufacturing: 23a Nyrang Street, Lidcombe NSW 2141, Australia
Telephone: (+61) 1300 666 595 Facsimile: (+61) 1300 666 594
Remote Power Supply Unit
Installation Manual
GREETINGS
Congratulations on choosing to use this Thomas & Betts product covered by our unique Through-Life Support system. This document is
designed to assist you during the installation of the product, to ensure the safety of yourself and others.
The Remote Power Supply Unit is designed to be installed quickly and easily however,
Thomas & Betts recommends that
you read this document thoroughly before commencing installation.
This device has been manufactured to provide
trouble free operation for many years, when treated with due care and maintained through regular and appropriate servicing.
SAFETY WARNING
In Australia and New Zealand, only licensed electricians are permitted by law to work with 240 Volt electrical installations.
Do not attempt to install or connect this product unless you are a licensed electrician.
Turn off and isolate the electrical supply before connecting this fitting to the building wires.
Do not touch the terminals of the terminal block when the light fitting is energised.
The only user serviceable parts are the lamp and battery pack.
Do not tamper with the fitting or the warranty will be void.
As the installer, it is your responsibility to ensure compliance with all relevant building and safety codes, (ie: AS3000, AS/NZS2293).
Refer to the applicable standards for data and mains cabling installation procedures and requirements.
6. Lamp operation:
Maintained:
Once powered up, in a maintained fitting the normal AC lamp (if present) should light up and stay on until
the power supply to the unit fails. The emergency function of the unit should only operate when the unswitched active power supply
fails or when somebody presses the manual test button located on the fitting.
Non-maintained:
Once powered up, in a non-maintained fitting the present lamp stays off. The emergency function of the unit
should only operate when the unswitched active power supply fails or when somebody presses the manual test button located on
the fitting.
TO REMOVE INSTALLED UNIT
Switch off the mains supplies to the unit. Remove the fuse from fuse holder and then unscrew the mounting screws of the unit. When
the unit is reconnected to the supply, it will need time to recharge its battery before it will be capable of a full length discharge again.
CONSTRUCTION SITES
Continuously switching on and off the mains supply to the fittings during the installation process (due to building works or for some other
reason), could cause the fittings to discharge and charge their batteries many times over a short period which may shorten the life of the
battery. Thomas & Betts does not recommend such practices and may not honour any warranty on the life of the batteries or the lamp
when subjected to such harsh operating conditions. In order to prevent damage to the battery, leave the unswitched active circuit turned
off at the circuit breaker, until the emergency lighting is required on the site.
TROUBLE SHOOTING GUIDE
If you’ve installed and connected the unit as per the instructions listed earlier and it doesn’t work properly, use the following table as a
guide to fixing the problem. Look up the type of fault in the left column and check the possible causes from the right column.
If the unit still doesn’t work after checking these possible causes, contact Thomas & Betts Service in Australia on 1300 666 595, Monday
to Friday, 8.30am to 4.30pm (AEST) and ask for help. Our trained service personnel will usually be able to take your call immediately and
assist you in resolving your difficulty. Thomas & Betts is committed to providing valuable Through-Life Support for its products.
Doc No: 29-01072
Contents
Electrical Safety Warning
Installation Instructions
Wiring Connections
Removal Method
Trouble Shooting Guide
Warranty Information (Included)
#
Fault
Possible Causes
1
Red LED not lit
(only applicable where used)
AC supply not connected; or
AC supply turned off; or
Battery not connected; or
Fuse missing; or
Test switch damaged
2
Red LED is lit (only applicable where used) but lamp
doesn’t come on when test switch is pressed
Lamp damaged; or
Battery pack damaged; or
Test switch damaged
3
Lamp is lit momentarily when test switch is pressed; or
When mains fail
Battery not fully charged (allow up to 24 hours); or
Battery pack damaged
PS702M:
12V maintained
unit designed to be used
remotely to provide escape
lighting for large areas or to
provide backup supply for the
lighting up of difficult or hostile
environments. The maximum
load limit is 35W if used in a
lift. The maximum load can be
70W if using as backup supply
to comply with AS/NZS2293.
Battery
PCA
Transformer
Output
12V DC
Mains 240Vac 50Hz
For switched illumination: Connect
incoming switched active, unswitched
active, neutral and earth to terminal
marked S/A, A, N and E respectively
For permanent illumination: Connect
incoming unswitched active, neutral
and earth to terminal marked A, N
and E respectively
(Note: Loop link between S/A and A)
Transformer
E
S/A
N
A
Output to load max 70W
