TA02966 E page 2 of 8
5
6
7
8
1
2
4
4
Ni-MH
3
16
17
18
15
19
25
04
1.0
GENERAL INFORMATION
BATTERY OPERATED
HYDRAULIC CRIMPING TOOL
The “BPLT14BSCRI” hydraulic tool is powered by a 14.4V Ni-MH
battery. It is a balanced tool for optimum control, quiet in operation
with very little vibration, with lightweight construction enabling the
operator to hold the tool in one hand and to position the cable
with the other hand. The operation buttons (operating/release)
are mechanically interlocked, the former is integrated into the
latter, so that accidental operation is prevented. A microprocessor
controls the tool operation and automatically cuts out the motor on
completion of the crimping operation, saving energy and extending
battery life. The residual battery capacity level is automatically
displayed after every cycle.
Catalog Number
“BPLT14BSCRI”
includes the following:
–
Basic tool complete with
battery
and
shoulder
strap
– Spare battery
– Battery charger
– Plastic carrying case
GENERAL CHARACTERISTIC
Head:
“C” shaped with large jaw opening, see Figure 4 (*).
Application range:
suitable for installing electric compression
connectors (lugs and splices) on conductors up to ....900 MCM
Crimping Force:
.................................................................. 14 ton
Rated operating pressure:
........................... 700 bar (10,000 psi)
Dimensions:
length ............................................................18.9”
width ...............................................................3.9”
height ...............................................................10”
Weight
(with battery): .......................................................... 19.6 lb
Motor
- direct current: ......................................................... 14.4 V
Battery
: ..................................................... 14.4 V − 3.0 Ah Ni-MH
External Supply:
.................................................12 V − 14.4 V DC
Recommended Oil:
..........................
AGIP ITE 360
or
equivalent
Operating Speed:
The tool has a twin speed pump that
automatically switches from a rapid advancing speed of the ram,
to a slower, more powerful crimping speed, as needed.
Safety:
The tool is provided with a maximum pressure relief valve.
ACOUSTIC NOISE
(Directive 2006/42/EC, annexe 1, point 1.7.4.2 letter u)
− The weighted continuous acoustic pressure level equivalent
A at the work place L
PA
is equal to ..................72,4 dB (A)
− The maximum value of the weighted acoustic displacement
pressure C at the work place L
pCPeak
is ..........< 130 dB (C)
− The acoustic power level emitted by the machine
L
WA
is equal to .................................................. 83,1 dB (A)
(Directive 2006/42/EC, annexe 1, point 2.2.1.1)
Test carried out in compliance with the indications
contained in UNI ENV 25349 and UNI EN 28662 part 1st
Standards, and under operating conditions much more
severe than those normally found, certify that
the weighted
root mean square in frequency of the acceleration
the upper limbs are exposed to for each biodynamic
references axis does not exceed 2.5 m/sec
2
.
RISK DUE TO VIBRATION
OVERALL VIEW
FIGURE 1
Operating
Button
Pressure
Relief Button
Head
Rotates 180°
Battery
Battery Capacity
Display
1. BEFORE USING THE TOOL, CAREFULLY READ INSTRUCTIONS IN
THIS MANUAL.
2. WHEN OPERATING THE TOOL, NEVER PLACE HANDS OR OTHER
BODY PARTS BETWEEN THE CRIMPING DIES.
3. DO NOT USE IN WATER OR IN THE RAIN.
4. DO NOT OPERATE WHEN DIES ARE NOT IN PLACE.
5. DO NOT SHORT THE BATTERIES.
6. ALWAYS RECYCLE THE BATTERIES.
7. DO NOT DISCARD BATTERIES INTO DOMESTIC REFUSE OR WASTE
DISPOSAL.
8. RISK OF ELECTRICAL SHOCK. DO NOT USE ON ENERGIZED LINES.
WARNING
1.4
1.5
1.1
1.2
1.3