manualshive.com logo in svg

Third Dimension GapGun Pro, Operator'S Manual

Share
Download
Third Dimension GapGun Pro Operator'S Manual Download Page 27

© Third Dimension Confidential Document D13-1604-OP-EN-3.3 

V7.5 

27

 

Safety 

BS EN 60825-1:2014- Safety of laser products  

BS EN 60950-1:2006+A12:2011 

–

 Information technology equipment safety. 

Declaration 

General 

The conformity to mentioned standards of each manufactured unit is ensured according our quality 
control standards BS EN ISO9001:2008. 

Europe 

             

 

The placement of the CE marking on our product Third Dimension Software Ltd is declaring, on its 
sole  responsibility,  conformity  with  all  of  the  legal  requirements  to  achieve  CE  marking.  Third 
Dimension  Software  Ltd  is  thus  ensuring  validity  for  that  product  to  be  sold  throughout  the 
European Economic Area (EEA).  

USA (FCC) 

 

This device contains : FCC ID: PVH0941 

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 
conditions: 

 

this device may not cause harmful interference, and 

 

this  device  must  accept  any  interference  received,  including  interference  that  may  cause 
undesired operation. 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital 
device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 
equipment  generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and 
used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 
communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 
particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television 
reception,  which  can  be  determined  by  turning  the  equipment  off  and  on,  the  user  is 
encouraged to try to correct the interference by one or more of the following measures: 

Summary of Contents for GapGun Pro


































Reviews:

No comments

Brands by name

Popular brands

Load more brands