manualshive.com logo in svg

THIEMAN Series TVLR 125A, Owner'S Manual

Share
Download
THIEMAN Series TVLR 125A Owner'S Manual Download Page 9

9.

MAINTENANCE GUIDE

The following inspection and maintenance operations should be performed at the recommended 

intervals or anytime the liftgate shows signs of abuse and improper or abnormal operation.

MONTHLY INSPECTION AND MAINTENANCE

Operate the liftgate throughout its entire operational cycle and check the following:

1.  Check that there are no unusual noises or vibrations.

2.   Check that the platform is level front to back and side to side when raised to bed height. If 

front to back adjustments are necessary, this can be done by adjusting nuts (A) on U-bolt 

(B) on platform block (C). See figure 2. If side to side adjustments are necessary, this can be 

done by adjusting nuts (D), nylon insert locknuts (E), and lockwashers (F) on tension rods 

(G) on anchor bracket (H). See figure 2.

IMPROPER MAINTENANCE OF THIS LIFTGATE MAY RESULT IN SERIOUS PERSONAL 

INJURY AND/OR DEATH.  Never use a liftgate, that has not been properly maintained. 

Follow all maintenance outlined in this manual, beginning with “Maintenance Guide” thru and 

including “Decal Maintenance - Inspection and Location of Decals”.

!

WARNING

Summary of Contents for Series TVLR 125A





























Reviews:

No comments

Brands by name

Popular brands

Load more brands