background image

Owner's Manual for Thern 5PA5 and 5PA10 Ensign Series Portable Davit Cranes

page 2

A11577I-0617

Two-Year Limited Warranty

Thern, Inc. warrants its products against defects in material or workmanship for two years from the date of purchase 

by the original using buyer, or if this date cannot be established, the date the product was sold by Thern, Inc. to the 

dealer. To make a claim under this warranty, contact the factory for an RGA number. The product must be returned, 

prepaid, directly to Thern, Inc., 5712 Industrial Park Road, Winona, Minnesota 55987. The following information 

must accompany the product: the RGA number, the date of purchase, the description of the claimed defect, and a 

complete explanation of the circumstances involved. If the product is found to be defective, it will be repaired or 

replaced free of charge, and Thern, Inc. will reimburse the shipping cost within the contiguous USA.

This warranty does not cover any damage due to accident, misuse, abuse, or negligence. Any alteration, repair or 

modification of the product outside the Thern, Inc. factory shall void this warranty. This warranty does not cover any 

costs for removal of our product, downtime, or any other incidental or consequential costs or damages resulting from 

the claimed defects. This warranty does not cover brake discs, wire rope or other wear components, as their life is 

subject to use conditions which vary between applications.

FACTORY AUTHORIZED REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE 

EXCLUSIVE REMEDY TO THE CONSUMER. THERN, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL 

OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS 

PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN 

DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on 

how long an implied warranty lasts, so the above limitation or exclusion may not apply to you. This warranty gives 

you specific legal rights, and you may also have other rights which vary from state to state. 

Note: Thern, Inc. reserves the right to change the design or discontinue the production of any product without 

prior notice.

About This Manual

The Occupational Safety and Health Act of 1970 states that it is the employer’s 

responsibility to provide a workplace free of hazard. To this end, all equipment 

should be installed, operated, and maintained in compliance with applicable 

trade, industrial, federal, state, and local regulations. It is the equipment owner's 

responsibility to obtain copies of these regulations and to determine the suitability 

of the equipment to its intended use.

This Owner’s Manual, and warning labels attached to the equipment, are to serve 

as guidelines for hazard-free installation, operation, and maintenance. They 

should not be understood to prepare you for every possible situation.

The information contained in this manual is applicable only to the Thern 5PA5 and 

5PA10 Ensign Series Portable Davit Cranes. Do not use this manual as a source 

of information for any other equipment.

The following symbols are used for emphasis throughout this manual:

Failure to follow ‘WARNING!’ instructions may result in equipment damage, 

property damage, and/or serious personal injury.

Failure to follow ‘CAUTION!’ instructions may result in equipment damage, 

property damage, and/or minor personal injury.

Important!

Failure to follow ‘important!’ instructions may result in poor performance of 

the equipment.

Please record the following:

Date Purchased:

Crane Model No.:

Crane Serial No.:

If sold with a winch:

Winch Model No.:

Winch Serial No.:

This information is required when 

calling the factory for service.

Summary of Contents for 5PA10

























Reviews: