Thermokon STC-DO8 Datasheet Download Page 1

 

 

» STC-DO 8 Type 3

 

 

  Wireless Actuator with 8 digital outputs 

 

 

 

 

 

Thermokon Sensortechnik GmbH, Platanenweg 1, 35756 Mittenaar, Germany  tel: +49 2778 6960-0  fax: -400  

www.thermokon.com

  

[email protected]

 

 

STC-DO8_Typ3_EasySens_Datasheet_en.docx   © 2021 

Datasheet

 

Subject to technical alteration 

Issue date: 12.01.2021 • A112 

 

 

 

 

 

» 

APPLICATION 

Bidirectional receiver with 8 digital outputs (or 12 with extension module STC-Plus 4DO). For heating/cooling control, fan coil control, control of 

lights and blinds etc. Incl. ext. receiving antenna (2,5 m).  

» 

TYPES AVAILABLE – TYPE 3 

Wireless receiver – multi relay 24 V 

STC-DO8 24 V type switch actuator 

Wireless receiver – multi relay 100..230 V 

STC-DO8 230 V type switch actuator 

» 

SECURITY ADVICE – CAUTION 

The installation and assembly of electrical equipment should only be performed by authorized personnel. 
The product should only be used for the intended application. Unauthorised modifications are prohibited! The product must not be 

used in relation with any equipment that in case of a failure may threaten, directly or indirectly, human health or life or result in 

danger to human beings, animals or assets. Ensure all power is disconnected before installing. Do not connect to live/operating 

equipment.  
Please comply with 

 

Local laws, health & safety regulations, technical standards and regulations 

 

Condition of the device at the time of installation, to ensure safe installation 

 

This data sheet and installation manual 

» 

NOTES ON DISPOSAL 

As a component of a large-scale fixed installation, Thermokon products are intended to be used permanently as part of a building 

or a structure at a pre-defined and dedicated location, hence the Waste Electrical and Electronic Act (WEEE) is not applicable. 

However, most of the products may contain valuable materials that should be recycled and not disposed of as domestic waste. 

Please note the relevant regulations for local disposal. 

 

 

517690

 

Summary of Contents for STC-DO8














Reviews: