Thermo NanoDrop One User Manual Download Page 23 | Manualshive

Page: 23 / 312

Thermo NanoDrop One User Manual Download Page 23

Measure dsDNA, ssDNA or RNA

Thermo Scientific

NanoDrop One User Guide

17

dsDNA, ssDNA and RNA reported values

The initial screen that appears after each measurement (see previous image) shows a summary
of the reported values. To view all reported values, press and hold the sample row. Here is an
example:

• sample details (application and sampling method used, i.e., pedestal or cuvette)

• sample name

• created on (date sample measurement was taken)

• nucleic acid concentration

• A260

• A280

• baseline correction

Related Topics

• Basic Instrument Operations

• Nucleic Acid Calculations

Setting for Nucleic Acid Measurements

To show the dsDNA, ssDNA or RNA settings, from the dsDNA, ssDNA or RNA
measurement screen, tap

>

Nucleic Acid Setup.

«
...
21
22
23
24
25
...
»

Summary of Contents for NanoDrop One

























































































































































































































































































































Reviews:

No comments