manualshive.com logo in svg

Thermo Scientific thermoscientific Vanquish Pumps C, Operating Manual

The Thermo Scientific Vanquish Pumps C is a state-of-the-art instrument essential for scientific research. To ensure smooth operation, we offer a detailed Operating Manual, available for free download from our website. Discover the full potential of this powerful product by accessing the manual now at manualshive.com.

Share
Download
background image

9

 • 

Pump-Specific Information

Page 224

Pumps C, Pumps F ( VC-Pxx, VF-Pxx) 

Operating Manual

9.2.5

Synchronizing the Injection Time with the Pump Strokes

To enhance the retention time precision with gradient applications, you
can synchronize the injection time of the Vanquish autosampler with the
strokes of the Vanquish pump. The synchronization ensures that all
injections are performed at the same phase of the pump cycle.

Synchronization is possible only when configured in the Chromeleon
software (refer to the 

Chromeleon Help

).

Then, the following properties are available in the Chromeleon software:

•

SyncWithPump

To enable synchronization, set the property to 

On

. To disable

synchronization, for example, for a specific application, set

SyncWithPump

 to 

Off

.

•

Pump

Shows the name of the pump to which the autosampler is linked.

Summary of Contents for thermoscientific Vanquish Pumps C









































































































































































































































































































Reviews:

No comments

Related manuals for thermoscientific Vanquish Pumps C

Camozzi 50 Series Mounting Instructions preview
50 Series
Brand: Camozzi Pages: 2
Latchways R20 User Instructions preview
R20
Brand: Latchways Pages: 80
Kapriol 27956 Manufacturer'S Instruction And Information preview
27956
Brand: Kapriol Pages: 28
GE Responder 2000 Service Manual preview
Responder 2000
Brand: GE Pages: 138
Landoll 2130 Operator'S Manual preview
2130
Brand: Landoll Pages: 83
Bante Instruments ORPscan10 User Manual preview
ORPscan10
Brand: Bante Instruments Pages: 6
Baoding Longer Precision Pump YZ Series User Manual preview
YZ Series
Brand: Baoding Longer Precision Pump Pages: 6
Cambridge Audio azur 640H Important Information preview
azur 640H
Brand: Cambridge Audio Pages: 2
Quanser Aero 2 User Manual preview
Aero 2
Brand: Quanser Pages: 12
Datalogic Matrix 400 Quick Reference Manual preview
Matrix 400
Brand: Datalogic Pages: 20
Datalogic Matrix 320 Product Reference Manual preview
Matrix 320
Brand: Datalogic Pages: 188
Haaga 677 Original Operating Instructions preview
677
Brand: Haaga Pages: 31
PASCO ME-9430 Instruction Manual And Experiment Manual preview
ME-9430
Brand: PASCO Pages: 30
TATU PT Operator'S Manual preview
PT
Brand: TATU Pages: 30
Rane HC6S Operator'S Manual preview
HC6S
Brand: Rane Pages: 4
Sabio 2010D Operation Manual preview
2010D
Brand: Sabio Pages: 182
Wang 2228D Maintenance Manual preview
2228D
Brand: Wang Pages: 146
Major tech MT474 Instruction Manual preview
MT474
Brand: Major tech Pages: 12

Brands by name

Popular brands

Load more brands