Thermo Scientific SRD-3200 Operating Instructions Manual Download Page 57

Page: 57 / 64

UltiMate 3000 Series:

SRD-3x00 Solvent Racks

Operating Instructions

Page

9 Accessories, Consumables, and Spare Parts

Accessories, consumables, and spare parts are always maintained at the latest technical

standard. Therefore, part numbers are subject to alteration. However, updated parts will

always be compatible with the parts they replace.

9.1 Standard Accessories

The following accessories are shipped with the instrument (subject to change without

notice). The part number always refers to the packing unit. Unless otherwise stated, the

packing unit is 1 unit. For more information, contact the Thermo Fisher Scientific sales

organization for Dionex HPLC Products.

Description

Quantity

in the kit

Part No.

SRD-3600 accessories, including:

Cable connecting the SRD and the UltiMate 3000 system

module (pump, NCS-3500RS, or NCP-3200RS)

6000.1006

Cap (to close the holes in the solvent bottle caps)

Included in

6000.0047

Bottle cap for solvent reservoirs

(including caps to close the holes in the bottle cap)

Included in

6270.0013

Solvent filter, including:

Filter holder (top and bottom parts) and

filter frit (stainless steel, porosity: 10 µm)

Included in

6268.0115

6268.0110

Retaining guide (solvent bottle)

Included in

6000.0042

1-liter solvent reservoir

2270.0012

Solvent supply line (analytical)

6030.2548

Tubing labels, white (A, B, C, D)

4 each

-----

Summary of Contents for SRD-3200

































































Search results

Summary of Contents for SRD-3200

Reviews:

Related manuals for SRD-3200

Brands by name

Popular brands

Thermo Scientific SRD-3200, Operating Instructions Manual

Search results

Summary of Contents for SRD-3200

Reviews:

Related manuals for SRD-3200

Brands by name

Popular brands