Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 33 / 67

background image

Get Started with Your Nicolet Summit OA Spectrometer

View Your Data with the OMNIC Anywhere
App

OMNIC Anywhere is a cloud-based application that allows you to view, explore, or share your data
from a connected PC, Apple computer, Android or iOS device.

Figure 1. OMNIC Anywhere in the web browser

With a Nicolet Summit OA spectrometer and a free Connect account, measure samples in the
classroom or lab, upload the data to your Connect account, and view, explore, or share the data on
another device in your dorm or workspace.

For instructions on creating a Connect account and viewing your data with OMNIC Anywhere, visit
“

Cloud-enabled FTIR Spectroscopy”.

30

Nicolet Summit OA Spectrometer User Guide

Thermo Scientific

«
...
31
32
33
34
35
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

Brand: National Instruments Pages: 12

Brand: Rodstation Pages: 28

QI-POWER-485-300

Brand: QEED Pages: 2

Brand: SATO KEIRYOKI Pages: 2

Brand: Omega Pages: 16

Brand: A&D Pages: 10

Brand: AXE Pages: 5

VACTEST GCD 200

Brand: BUSCH Pages: 12

Brand: Fluke Pages: 5

Brand: PCE Health and Fitness Pages: 4

Brand: UNI-T Pages: 11

Brand: South Pages: 54

Brand: Simpson Pages: 19

Brand: PCE Instruments Pages: 25

InnovaSonic 205i

Brand: Sierra Pages: 12

Brand: Omega Pages: 2

Brand: DRUCK & TEMPERATUR Leitenberger Pages: 64

Brand: BIRD Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands