Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 28 / 67

background image

Install a USB Wireless Adapter

You can connect your Nicolet Summit OA spectrometer to a wireless network using the optional USB
wireless adapter. If you purchased the adapter with your spectrometer, it comes preinstalled.

To install the USB wireless adapter, insert the adapter into any USB port. For a more permanent
installation, install the adapter in a port under the instrument cover.

❖

To install a USB wireless adapter

1. Insert the adapter into any available USB port.

2. The system will recognize the adapter automatically. For information on connecting to a network

using your adapter, see support from Microsoft.

❖

To install using a USB port under the instrument cover

This installation requires you to remove the crystal plate and instrument cover.

1. Follow the instructions in

"Replace the Cover"

to remove the crystal plate and instrument cover.

2. With the cover removed, insert the adapter in either available USB ports.

Thermo Scientific

Nicolet Summit OA Spectrometer User Guide

25

Get Started with Your Nicolet Summit OA Spectrometer

«
...
26
27
28
29
30
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

TUNICS T100S-HP

Brand: Yenista Optics Pages: 66

Brand: RADWAG Pages: 12

Brand: bentrup Pages: 9

Brand: Mic Pages: 2

Brand: Det-Tronics Pages: 18

Brand: Laserworld Pages: 5

Brand: XS Instruments Pages: 41

Brand: Bante Instruments Pages: 26

Brand: IS Technologies Pages: 21

Brand: Mityvac Pages: 24

Brand: dacell Pages: 29

Brand: VOLTCRAFT Pages: 4

Brand: Televes Pages: 2

Brand: Vaisala Pages: 2

Brand: SKF Pages: 12

Brand: GREISINGER Pages: 20

Brand: FLIR Pages: 21

Brand: DAKOTA ULTRASONICS Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands