Thermo Scientific KingFisher Flex Service Manual Download Page 165

Page: 165 / 228

KingFisher

Flex

Thermo Fisher Scientific

Service Manual

Version 1.1

Software

7-11

7.1.11.11 PAR -set nonvolatile parameters

This command is used to set non volatile parameters of the instrument. Related parameters are
grouped under the same group code.

Command:

PAR ui_group values

ui_group

The parameter group to set.

values

List of values to set for the parameters.

Response:

PAR

PAR END ui_status

Recordable:

Non volatile parameters which can be set by the

PAR

command:

Group 0

Set instrument serial number.

Command:

PAR 0 a_serial_number

a_serial_numberInstrument serial number as an ASCII string.

Group1

Set stepper home sensor offset.

Command:

PAR 1 si_rotate_offset si_magnet_offset si_head_offset

si_heater_offset si_shield_offset

si_rotate_offset

Rotate stepper home sensor offset in steps.

si_magnet_offset

Magnet stepper home sensor offset in steps.

si_head_offset

Head stepper home sensor offset in steps.

si_heater_offset

Heater stepper home sensor offset in steps.

si_shield_offset

Shield stepper home sensor offset in steps.

The instrument adds the offsets to the existing offsets. The initial offsets are all 0.

Group 2

Set instrument name.

Command:

PAR 2 a_name

a_name

Instruments name as an ASCII string. The instrument

responds with this name to the

VER

command. The default

name is ‘

KingFisher 96

’.

Group 3

Set acceleration values for acceleration table calculation. Also a new ramp for
the stepper is calculated and saved to the NV memory.

Summary of Contents for KingFisher Flex





































































































































































































































Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands

Thermo Scientific KingFisher Flex, Service Manual

Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands