manualshive.com logo in svg

Thermo Scientific iCAP RQ ICP-MS, Pre-Installation Requirements Manual

Share
Download
Thermo Scientific iCAP RQ ICP-MS Pre-Installation Requirements Manual Download Page 28

Site Preparation

Placing the System

Thermo Scientific

iCAP RQ Pre-Installation Requirements Guide (P/N BRE0009927, Revision A)

2-13

Placing the Data System

For the data system, Thermo Fisher Scientific recommends using one 
workbench with minimum dimensions of 1.00 m × 1.20 m. The 
workbench must be capable of supporting the weight of the data system 
and a printer, if applicable. A printer is not delivered with the 
instrument. The iCAP RQ ICP-MS instrument is connected to the 
computer via a USB cable, see 

Figure 2-11

.

Figure 2-12

 shows typical data system hardware components.

Labeled Components: 1=data connection to computer 

Figure 2-11. 

Connections for computer

Figure 2-12. 

Typical data system workbench

1

monitor

computer

wall outlet for data system components 
120 or 230 V AC

 communication

cables USB and

Ethernet

Summary of Contents for iCAP RQ ICP-MS








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands