Thermo Scientific GENESYS 10S Vis User Manual Download Page 27

Page: 27 / 134

Accessories

Cell Holders and Cell Holder Accessories

Thermo Scientific

GENESYS 10S Vis User Guide

• use test tubes

• measure solid samples in the filter holder

• regulate sample temperature via an external liquid recirculator

you must install the appropriate cell holders. The 6-Position Cell Holder installed in the
spectrophotometer can easily be removed to install other accessory cell holders. See

“Removing the 6-Position Cell Holder and the Single Cell Holder”

page 20

Installing the 6-Position Cell Holder and the Single Cell Holder

To install the 6-Position Cell Holder and the Single Cell Holder

1. Open the sample compartment door and let it rest on its hinge.

2. With one hand, carefully lower the cell holder straight down into the sample

compartment.

Figure 1.

6-Position Cell Holder

Captive thumbscrew

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands