background image

5

Warning

THIS PRODUCT CONTAINS REFRACTORY CERAMIC,

REFRACTORY CERAMIC FIBER OR FIBERGLASS

(GLASS WOOL) INSULATION WHICH CAN PRODUCE

RESPIRABLE FIBERS AND DUST WHEN HANDLED.

THESE FIBERS OR DUSTS CAN CAUSE IRRITATION

AND CAN AGGRAVATE PRE—EXISTING RESPIRATORY

DISEASE. REFRACTORY CERAMIC INSULATIONS MAY

CONTAIN OR MAY FORM CRYSTALLINE SILICA (CRYS-

TOBALITE) WHICH MAY CAUSE LUNG DAMAGE (SILI-

COSIS).

THE INTERNATIONAL AGENCY FOR RESEARCH ON

CANCER (IARC) HAS CLASSIFIED REFRACTORY

CERAMIC FIBER AND FIBERGLASS AS (2B) POSSIBLY

CARCINOGENIC. IARC HAS CLASSIFIED CRYSTALLINE

SILICA AS (2A) PROBABLY CARCINOGENIC.

The insulating materials are located in the door, the hearth

collar, in the chamber of the product or the top plate assem-

bly. Tests performed by the manufacturer indicate that there

is no significant risk of exposure to dust or respirable fibers

resulting from operation of this equipment under normal con-

ditions. However, there may be a risk of exposure to res-

pirable dusts or fibers when repairing or maintaining the

insulating materials, or when otherwise disturbing the mate-

rials in a manner which causes release of dust or fibers

therefrom. Through the use of proper handling procedures

you can work safely with these insulating materials and min-

imize any exposure. Accordingly, before you repair or

replace any insulating materials, or perform any other ser-

vicing on this product which could disturb or cause exposure

to dust from insulating materials, you should consult the

appropriate Material Safety Data Sheets (MSDS’s) for such

products with respect to proper handling and appropriate

protective equipment. For additional MSDS’s, or additional

information concerning the handling of refractory ceramic

products, please contact the Customer Service Department.

REFER SERVICING TO QUALIFIED PERSONNEL.

1-800-553-0039

S

AFETY

I

NFORMATION

Summary of Contents for Cimarec HP194515












Reviews: