Thermo Scientific AquaSensors AnalogPlus User Manual Download Page 28

Page: 28 / 33

Thermo Scientific AquaSensors

™

AnalogPlus

™

Differential pH Sensor User Guide

AnalogPlus Differential pH Sensors and Hardware for 1.0-Inch Bodies

Model Number

SP Differential pH Sensor in 1-inch body. Cable connects to any AV88 Universal Analyzer, P99 Analyzer or

compatible differential pH analyzers. Integral ground rod, temperature, replaceable salt bridge and reference

solution. Standard 1-inch NPT mounting. Options for tri-clamp and ball valve mounting.

Body Material

2 CPVC (Low Cost, All-Purpose)

3 PEEK® (Food Grade, Chemically Resistant)

Measurement Electrode

1 General Purpose Glass (Standard)

2 HF Glass(recommended for hydrofluoric acid applications)

3 Low Temperature Glass (recommended for temperatures below 5°C)

4 Pure Water Glass (recommended for conductivity below 10µS/cm)

5 High Temperature Glass (recommended for temperatures above 85°C)

Sensor Tip

A Protected Electrode (Standard)

B Process Flat (reduce protrusions)

Temperature Element and Hookup

7 PT1000 for AquaMetrix Analyzer Hookup

8 NTC300 for P99 & GLI/Hach Analyzer Hooku

9 PT1000 for AV88 Universal Analyzer Hookup

Ground Rod

D 316 Stainless Steel (for HF or customer specified applications)

E Titanium (standard configuration)

F Hastelloy C (for heavy industrial applications )

Cable Length

10 10 Feet

20 20 Feet

30 30 Feet

xx Where xx = Number of Feet

AnalogPlus pH Sensor Part Number

Part Number Suffixes for Special Body Construction

-IN15

-S20

-S25

1.5-inch Ball Valve Insertion Mount (No front threads)

Sanitary Style 2.0” Tri-clamp.

Sanitary Style 2.5” Tri-clamp.

Mounting Hardware

Description

Part Number

1.5” Union Mount Assembly

Tee with locking collar, 316 Stainless Steel

Tee with locking collar, CPVC

MH3041

MH3042

1” Tee

Schedule 40, Stainless Steel

Schedule 80, CPVC

MH3011

MH3022

Immersion Assembly

7 ft PVC extension with junction box – 1” Sensors

MH3083

Immersion Assembly

w/Swivel Rail Mounting

7 ft PVC extension with junction box – 1” Sensors With swivel hand rail mount.

MH1242

Immersion Assembly

w/Swivel and Ball Float

7 ft PVC extension with junction box – 1” Sensors With swivel hand rail mount and

inflatable float.

MH1252

1.5” Ball Valve Assembly

Low Pressure, CPVC

Low Pressure, Stainless Steel

High Pressure, CPVC

High Pressure, Stainless Steel

MH1112

MH1111

MH1122

MH1121

Tri-Clamp Tee Assembly

2” Tri-Clamp tee, gasket and clamp, Stainless Steel

MH1261

Junction box

Extension Cable

For extension cables. Terminal strip included.

AnalogPlus extension cable

JBOXX01

APECxx; xx=ft

Wash Hardware

Attach purge block to sensor body. Works with compressor & AV88 wash relay.

MH1132

Summary of Contents for AquaSensors AnalogPlus


































Search results

Summary of Contents for AquaSensors AnalogPlus

Reviews:

Related manuals for AquaSensors AnalogPlus

Brands by name

Popular brands

Thermo Scientific AquaSensors AnalogPlus, User Manual

Search results

Summary of Contents for AquaSensors AnalogPlus

Reviews:

Related manuals for AquaSensors AnalogPlus

Brands by name

Popular brands