Thermo Scientific Applied Biosystems SeqStudio Genetic Analyzer User Manual Download

Page: 18 / 242

Cartridge storage

Table 1

Storage information for the SeqStudio

™

Genetic Analyzer Cartridge (Cat. No. A33671)

Condition

Description

Shipping

Shipped at 2–8°C.
Store upright at 2–8°C upon receipt.
Save the white storage box and optical cover for off-instrument cartridge storage.

On-instrument storage

For routine use, can be used and stored on the instrument for up to 4 months. If

you store the cartridge on-instrument:

• The instrument must be powered on.
• A Cathode Buffer Container must also be installed.

The instrument keeps the components under the following conditions when it is

powered on and in Cartridge storage mode:

• Optical detection window—Covered
• Capillary array electrodes—Submerged in cathode buffer (buffer must be

above the fill line in the Cathode Buffer Container)

• Polymer—Chilled
• Anode buffer—Ambient temperature

IMPORTANT!

The instrument does not maintain the correct temperature

conditions for the cartridge when it is powered off. Avoid cartridge exposure to

ambient temperature.

Off-instrument storage

For intermittent use, can be stored off-instrument until the expiry date on the label

or up to 4 months after first use. Store upright at 2–8°C, with an integrated

capillary protector (ICP) and optical cover installed (see “Store the cartridge“ on

page 163).

Note:

After you remove the cartridge from the instrument, install an ICP within a

few minutes. Avoid cartridge exposure to ambient temperature.

Reuse

Can be removed from an instrument then inserted again on the same instrument

or a different instrument, if it was stored properly at 2–8°C and has not expired or

exceeded 125 injections.
Information about the cartridge installation and usage is retained in the cartridge

history (Settings

Cartridge

Instrument–cartridge history).

Chapter 1

Product information

SeqStudio

™

Genetic Analyzer consumables

SeqStudio

™

Genetic Analyzer Instrument and Software User Guide

Summary of Contents for Applied Biosystems SeqStudio Genetic Analyzer



















































































































































































































































Search results

Summary of Contents for Applied Biosystems SeqStudio Genetic Analyzer

Reviews:

Related manuals for Applied Biosystems SeqStudio Genetic Analyzer

Brands by name

Popular brands

Thermo Scientific Applied Biosystems SeqStudio Genetic Analyzer, User Manual

Search results

Summary of Contents for Applied Biosystems SeqStudio Genetic Analyzer

Reviews:

Related manuals for Applied Biosystems SeqStudio Genetic Analyzer

Brands by name

Popular brands