restoration. The display windows will
flash. Press any button to stop flashing.
4.4 Accessory Installation
1.
(figure 1), and
r
2. Split the Fixed Tube Rack and the
holder (88882117, 88882118,
88882119), put the holder on tray and
fix it with the 4 sunk screws
.
3. Vertically clip the Fixed Tube Rack into
the holder and make sure there is no
gap between the rack and the holder
.
4. Insert the test tube.
Note:
When using single test tube, it is
recommended not to set the speed too
high because the imbalanced load may
damage the instrument.
Loosen the screws of the tray with a
cross screwdriver
eplace the standard tray with platform
large (figure 2).
(figure 3)
(figure 4)
9
|
Section 4 Operation
Finish Operation
After the operation is finished, press the
power switch at the back right side of
the instrument and put it into the “
O
”
state. Unplug the instrument and store
the instrument according to the storage
guide.
Alarm System
Exceed the speed limit: After entering the
operation mode for 5s, if the actual
speed of the instrument is 0 or more
than 1200rpm, the instrument will alarm
immediately.
Err1: After entering the operation mode
for 10s, and the instrument runs steadily
(running stability means that the actual
speed of the instrument is within the set
value of ±10rpm). If the speed exceeds
the set speed of ±10rpm, the instrument
stops running and buzzes to alarm, Run
indicator light goes off, and "Err1" is
displayed in the Speed display window.
End of timer: The instrument buzzing
alarm, the "End" is displayed in the Speed
display window.
When the instrument alarms, press any
key, the instrument is back to the
standby mode.
Power Recovery
If the power supply is cut off suddenly
while the instrument is in operation, the
unit will automatically run at the
previously set parameter upon power
figure 1
figure 2
figure 3
figure 4
Digital Microplate Shaker 10
4.2 Installation
1. Connect all the components according
to the figures shown on page 4 of this
manual. Use grounded power outlet.
2. Press the power switch "I" side and
switch on the instrument.
4.3 Settings
Time Settings
1. Continuous mode
Press the “ ” or “ ” arrow button
below the Time display window. When
the number shown on the Time display
window starts flashing, press “ ”
arrow button to decrease the time to
00:00 and then release the button. The
time setting is finished after the number
shown on the Time display window
flashed twice.
2. Timer mode
Press the “ ” or “ ” arrow button
below the Time display window. When
the number shown on the Time display
window starts flashing, press “ ” or
“ ” arrow button to increase or
decrease the time value. Release the
button when the time shown on the
Time display window reaches the set
value. The time setting is finished after
the number shown on the Time display
window flashed twice.
Speed Settings
Press the “ ” or “ ” arrow button
Run
Stop
Run
Stop
below the Speed display window. When
the number shown on the Speed display
window starts flashing, press “ ” or
“ ” arrow button to increase or
decrease the speed value. Release the
button when the speed shown on the
Speed display window reaches the set
value. The speed setting is finished after
the number shown on the Speed display
window flashed twice.
Note:
Press the “ ” or “ ” arrow
button for a longer time to accelerate the
setting.
Run and Stop
Press “ ” button and the instrument
will start running with the specified
settings and the Run indicator light will
be on.
The Time display window will show the
cumulative time (Continuous Mode), or
remaining time (Timer Mode) and the
Speed display window will show the
current speed.
Press “ ” button again and the
instrument will slow down until it stops.
The instrument will then be in standby
and the two display windows will show
the set values.
Note:
To ensure shaking operation
smooth and steady, it may take 1minute
for the microprocessor control system to
accelerate the tray to the set speed.
