Thermo Scientific 42iQD Instruction Manual Download Page 221

Page: 221 / 286

Servicing

DMC PMT Cooler and Reaction Chamber Replacement

Thermo Scientific

42iQD Instruction Manual

7-31

Figure 7–35.

Photo Reaction Chamber Cleaning, Hardware

Pull reaction chamber outwards.

Equipment Damage

Some internal components can be damaged by small

amounts of static electricity. A properly grounded antistatic wrist strap

must be worn while handling an internal component.

▲

To reinstall reaction chamber, follow previous steps in reverse, making

sure to back fill the cooler with dry air or nitrogen prior to installing

reaction chamber.

Reinstall the measurement bench. Refer to

Figure 7–34

and

Figure 7–

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands