manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 220

Servicing 

DMC PMT Cooler and Reaction Chamber Replacement 

7-30

     42iQD Instruction Manual 

Thermo Scientific 

 

Use the following procedure to clean or remove the reaction chamber. 
Equipment Required: 

Phillips drive, #2 

1.

 

Turn the instrument OFF, unplug the power cord, and remove the 

cover. 

2.

 

Remove cooler/reaction chamber DMC as described in “

PMT Cooler 

Shroud Removal

” in this chapter. 

3.

 

Unplug heater J8 from board. 

 

Figure 7–34.

 Photo Reaction Chamber Cleaning, Electrical 

4.

 

Disconnect plumbing as shown. 

5.

 

Using a 9/64-inch hex drive, unfasten three #8-32 socket cap head 

screws. 

Reaction Chamber 

Cleaning and/or 

Removal 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands