Section 6 – SR-2 Service Procedure A48A
Diagnostics
Step Action
Result
Comments
1. Plug the standby power cord into
a known good power supply and
turn the unit on.
2. Using a Fluke Meter, test the L1,
L2, and L3 circuits at the input to
the terminals where the Brown,
Blue and Black wires are
connected.
The voltage should be between
200 - 500 VAC between circuits.
If not, repair as necessary to
supply the needed voltage to the
unit.
3. Check the #8F and CH circuits to
the phase detect module. 12-24
VDC must be present from #8F to
CH.
If this power is not present, check
the #8 circuit from the On/Off
switch.
4. If correct power is present in the
test above then the ER circuit on
the interface board should have
12-24 VDC present.
If power is not present replace
the phase detect module.
Removal and replacement of the
phase detect module is detailed
on a previous page.
5. If LED 6 on the interface board is
on then the 7EH circuit should
have 12-24 VDC present.
If power is not present check the
Diesel/Electric Relay circuit on
the interface board.
6. If the unit is calling for operation
(LED 6 is on) one of the phase
select contactors should be
energized.
If neither contactor is energized
check for 12-24 VDC. If voltage is
not present replace the phase
detect module.
Removal and replacement of the
phase detect module is detailed
on a previous page.
Page 5
P41RA48A 30 January 2005
Summary of Contents for SR-2 SmartReefer2
