TK 61552-2-MM-EN
27
S
Se
errv
viicce
eW
Wa
attcch
h
™
™
:: ServiceWatch is standard equipment. It records operating events, alarm codes,
and compartment temperatures as they occur and at preset intervals. This information is
typically used to analyze unit performance. Use a USB port to download the ServiceWatch data.
IIm
mp
po
orrtta
an
ntt:: A ServiceWatch download can be helpful when diagnosing a problem in a unit with
an SR-3 Controller. Therefore, it is recommended that a ServiceWatch download be
performed to help diagnose a problem. A ServiceWatch download must be
preformed before contacting the Thermo King Service Department for assistance in
diagnosing a problem. Refer to the for information about downloading the
ServiceWatch Data Logger and viewing the data.
C
Ca
arrg
go
oW
Wa
attcch
h
™
™
:: CargoWatch data logging requires the installation of optional sensors. Up to six
temperature sensor/probes and four door switches can be installed. CargoWatch also logs the
setpoint. Use the USB Port to download the CargoWatch data. If optional temperature sensors
are installed, the readings are displayed as Datalogger Sensor (1-6) Temperature in the sensor
readings. See “Using the Sensors Key” in the Operating Instructions Chapter.
A printer can also be used to print a report of the optional sensor readings. See “Data Logger
(CargoWatch)” in the Operating Instructions Chapter.
U
US
SB
B P
Po
orrtt:: A Universal Serial Bus (USB) port is provided on all units. If installed, it is located next
to the HMI. Standard USB flash drives that have been programmed with WinTrac can be used.
Use of a flash drive eliminates the need for an on-site computer and does not require cables.
IIm
mp
po
orrtta
an
ntt:: The flash drive must be properly configured and the desired features must be
enabled using WinTrac software.
Using a properly configured and enabled flash drive, the following functions may be available:
•
Download the ServiceWatch Data Logger
•
Download the CargoWatch Data Logger
•
Flash load Base Controller Software
•
Flash load HMI Control Panel Software
•
Send OptiSet Plus Files
•
Retrieve OptiSet Plus Files
C
Ca
arrg
go
oW
Wa
attcch
h P
Po
orrtt:: The CargoWatch port is used to download the CargoWatch Data Logger and
to flash load software to the HMI Control Panel. It is located on the Control Panel.
S
Se
errv
viicce
eW
Wa
attcch
h P
Po
orrtt:: The ServiceWatch port is used to download the ServiceWatch data logger
and to flash load software to the Base Controller.
P
Prriin
ntte
err P
Po
orrtt:: This port is used to print trip records from the CargoWatch Data Logger.
TK BlueBox
Beginning in 2017, the TK BlueBox communication device is fitted as standard on new SLXi
Series units and is also available as an option on certain other units. The TK BlueBox offers real-
time information and two-way communication.
A Maintenance Menu feature called Telematics Status is available that allows the user to check
for possible telematics status alarms. Telematics status alarms differ from standard unit alarms;
they do not appear as alarms on the HMI main screen if there is an issue with the TK BlueBox.
The user is required to access the Maintenance Menu and select Telematics Status to determine
if status alarms are activated.
The status alarms are listed below. Refer to the TK BlueBox Diagnostic Manual (TK 56391) for
complete information and diagnostic procedures.
T1
SIM Not Inserted
T8
Data Delayed to TracKing
™
T2
Check SIM PIN
T9
CAN Communication Issue
T3
Check APN Configuration
T10
Check iBox
™
Third Party
T4
Check GSM Antenna
T11
iBox System Issue
T5
No GSM Coverage
T12
Check Backup Battery
